Models > 5KSM175PSEIB4 > Instructions

5KSM175PSEIB4 Whirlpool Mixer - Instructions

Jump to:

All Instructions for the 5KSM175PSEIB4
121 - 135 of 182
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Gennette from Yuba City, CA
Parts Used:
WPW10672617
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
The Coating On My Flat Beater Had Chipped; Did Not Think It Was Safe Continue Using.
It was actually not a repair problem; just a replacement of a part. I ordered it one day and the next day the part was here. I have never had such a quick turn around in anything I have ordered. Thank you!!!!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from Aitkin, MN
Parts Used:
WPW10191926
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Screw cap or retainer wore out and wouldn't hold the bowl tight
Removed the old screw cap and installed the new one-only has 3 screw to remove and re install. VERY easy. Fits perfectly
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Tolland, CT
Parts Used:
WPW10112253
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Sticky back disc on Orbital sander came apart (from old age )
remove 3 screws ,remove old sanding disc replace with new installl screws
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ashok from Sterling, VA
Parts Used:
WPW10112253
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
The worm gear was damaged
I how the video for replacing the worm gear on your website. It help me a lot. I followed step by step instruction display on video. It was great help.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gordon from Seneca, SC
Parts Used:
WPW10112253
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers
Mixer jammed, then would not mix, motor ran
Wish that I had known about the video before disassembling. I did not know if it needed a part or was just jammed. It was clear that i needed a worm gear. So I ordered that. It turned out that I needed the Pinion Shaft w/ gear too. So another order. The shipping far exceeded the cost of the parts. NOTE: Clear off as much grease as necessary to be certain that there are no stripped gears anywhere, the order the parts. I took the mixer head off of the stand. I would suggest that you take a bath towel, roll each end towards the center, and place the mixed head so that it is supported on both sides by the towel rolls. NOTE2: Shipping was great 2 days or less. One part arrived on a Saturday. P>S> I do not know the age of this mixer. The age drop down menu should have an UNKNOW option.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Peter from Brooklyn, NY
Parts Used:
WPW10380496, WP9709276, WP9709194
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
Motor ran rough and weak with squeaking sounds
Initially I thought this was due to worn motor brushes. I replaced the brushes but it did not fix the problem. Stator tested OK with an ohmmeter so I figured it was the armature part #PS3651001. Ordered that next and that fixed the problem. Spent 25 dollars which beats buying a new one. Next time I'm buying a used one from the 60s or 70s when they made them better! One tip - I had a hard time removing the pin that you need to remove the helical gear. Heating it with a heat gun helped a lot, also helped with replacing it after.
Was this instruction helpful to you?
Thank you for voting!
Customer:
john from las Vegas, NV
Parts Used:
WPW10380496
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers
Brushes go in only one way & not same each
Took it to repair shop
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from Spring Valley, CA
Parts Used:
WPW10191926
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers
37 year old screw cap worn, wouldn't hold bowl with heavy dough
Easy removal of old screw cap, but new one didn't just drop in. Had to scrape paint and a little aluminum to make it fit. Finally did, and it works fine now.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Anthony from Altadena, CA
Parts Used:
WPW10112253
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Worn out worm (nylon) gear.
Followed up by your précised video, and print copy's which helped me a lot. That's easy!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Wade from McDonough, GA
Parts Used:
WPW10672617
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Beater/Mixer Ran many hours, Rubbed paint off tip
Ordered new paddle beater, rmoved old beater from mach, took new beater from plstc bag, inserted into mixer in appropriate plc, turned on mixer. YES!!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Erwin from Northport, ME
Parts Used:
WPW10112253
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers
Worm gear broken.
Followed directions video on line. good directions.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ashley from Dayton, OH
Parts Used:
WPW10380496, 4162546
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers
Nothing would happen when we turned it on...
The brushes on the inside of the motor were destroyed. We thought that it would be easier to just replace the brush holder and the brushes, however, the brushes were easy! and QUICK! The brush holders...not so much. We had lots of problems getting the brush holders into place because of a metal piece that had to fit perfectly on top of the brush holder. It made it easier when I held the mixer upside down (we dissembled it) and my husband did his magic on fixing the brush holders. Pray that you won't need to replace the brush holders because it was NO FUN...but the brushes were QUICK AND EASY :)
Was this instruction helpful to you?
Thank you for voting!
Customer:
Barbara from Rockdale, IL
Parts Used:
WPW10380496
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
machine not running-broken worm gear?
After I dropped a part of the shield into my mixer the motor screamed and I unplugged the mixer. I found out I had a broken worm gear. I then order the part and per the helpful video I did the repair and I also changed the brushes my mixer is up and running waiting for the holiday baking season thanks to Part select.com Very easy Instructions to follow I am very happy with the results. Thanks Barbara
Was this instruction helpful to you?
Thank you for voting!
Customer:
Nick from Naperville, IL
Parts Used:
WPW10380496
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
My wife was complaining of a loud grinding noise.
I replaced the brushes. I didn't realize that I've put one of them wrong. Reminder for next time the brushes have to touch the rotor of the motor. It took me a little bit to understand but the brushes can go in and not touch the rotor. It works very quietly now. Thank you PartSelect for your infos and knowledge.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Thomas from Dickson, TN
Parts Used:
W11192794, W11192794
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Replaced main gears
1. Removed the mixer from the base by removeing the pivot pin at the mixer base support. 2. removed the retainer ring from the housing. 3. removed the pin from the shaft. 4. removed 5 philips machine screws from the round base. 5. removed the round base from the mixer housing. 6. removed the o-ring from the shaft. 7. removed the shaft and large worm/pinion gear from the shaft. 8. pressed out the pinion drive gear from the mixer. The reverse operation repaired the mixer to new condition.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 5KSM175PSEIB4
121 - 135 of 182