Models > KG25H1XER5 > Instructions

KG25H1XER5 Whirlpool Mixer - Instructions

Jump to:

All Instructions for the KG25H1XER5
106 - 120 of 195
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Michael from Tomahawk, WI
Parts Used:
W11192795, W11192795, WP3400814
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Wrench (Adjustable)
Gears ground when roller attachment applied.
Took screw off band. This revealed 4 screws to upper housing. Removed 4 screws and lifted upper housing off . To my surprise I found no screws holding gear housing cover in place. You could tell they were there at one time. Should be 4. I removed cover disasembled what was left of gears. Cleaned old grease ordered parts. Thought since there was only 1 screw on diagram it would ship 4. No big deal. After recieving parts further inspection revealed no screws holding motor in place. This blows me away. Anyway off to local hardware store for more screws. Got home slapped it togethere in 10 minutes. Ordered this off TV about 6 years ago. They must have had it in for repair and forgot to put it back together. All that aside it runs better than ever. Thanks much Michael
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
jose from denver, CO
Parts Used:
W11192795
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
attachment driver will not work
Remove screw at back of mixer,remove metal sleve and remove three more screws (front and sides. remove screws and plastic cap of gear box then remove holding ring in post and remove damaged ring installation is opposed of removal.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mary from York, PA
Parts Used:
8212396, WP9709511, W11192795, W11192795
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Grinding sound
Replaced cracked plastic gearcase/transmission with new medal one and replaced hub bevel gear attachment, bevel gear and gasket.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kenneth from Brookings, OR
Parts Used:
W11086780
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
mixer beater quite
disassembled unit gear head and replaced broken part, then reassembled
0 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mitchell from Santa Fe, NM
Parts Used:
W11086780
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Mixer would not spin, worm gear worn out.
The repair is actually quite simple. The Snap Ring Pliers are essential. Make sure you clean out all the old grease in the machine and replace with new grease. The metal dust will act like sandpaper and destroy your new gear. There are several videos on YouTube which go through the process of repair and part replacement, I found these quite helpful. Good luck! DIY!!!!
Was this instruction helpful to you?
Thank you for voting!
Customer:
fatema from dublin, CA
Parts Used:
WP9709231, W11086780, WP9703680
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers
Gears were slipping
Noticed worm gear was worn out, ordered the parts, it came very next day. On YouTube instructions were very easy to follow. Important point to remember,I washed the parts in water with chlorine in it. Retaking ring was tough to take out, as I did not have parrot beak plier, could not find it at Home Depot or Lows. Putting the retaining ring I used circular nut driver, to press it on the shaft to slide down by hammering it. While assembling follow the instruction step by step from the you tube. Machine works smoothly. Performing well. Thanks to part select, excellent web page, efficient delivery. I would recommend them to all.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Leonard H. from Rustburg, VA
Parts Used:
WP9709511, W11192795, W11192795
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
bevel gear chewed up by the hub bevel gear
took mixer apart down to removal of gear case cover.upon removal of this cover found the bevel gear and hub bevel gear chewed up .removed them both then replaced them both.and also had to solve a clearence problem between the 2 gears they were too loosely meshing. so had to push the hub retainer closer to take up the meshing slack.not sure my repair will hold but i have another set of gears and another solution that will surely fix it.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ronny from Clearwater, KS
Parts Used:
WP9707223, W11086780
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Worm Gear teeth was stripped
Removed top cover, remove snap-ring on shaft, slide top gear and worm gear off. Clean all the grease out and clean parts. Installed new worm gear and parts. Repacked with new grease, careful not to much, leaving room for expansion.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Marie Ann from Dover, MA
Parts Used:
W10807813
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Needed new mixer beaters
I replaced my kitchen Aid mixer beaters. I bought two replacement beaters. They fit perfectly
Was this instruction helpful to you?
Thank you for voting!
Customer:
Linda from Lynden, WA
Parts Used:
WP9709194
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Thumb screw
the plastic covering the thumb screw cracked almost half way and lost the piece....so the new one is being used to replace this old one...very easy to install
Was this instruction helpful to you?
Thank you for voting!
Customer:
Susan from Santa Barbara, CA
Parts Used:
W10807813
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Paint was peeling off the old beater.
I put the beater in the mixer when I wanted to make a cake. I wouldn't call it a repair. The most amazing thing was that it arrived the day after I called and ordered it!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Nancy from North Andover, MA
Parts Used:
WPW10731415
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
One of the wire spokes had broken on my wire whip.
This is Cindy, the person who ordered the part for Nancy. She was absolutely thrilled that she got it the very next day! She thought I had paid extra for overnight delivery! She is so pleased she doesn't have to listen to the noise the other wire whip was making when turned on. Cindy
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rodney from Thornton, NH
Parts Used:
W11086780
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
worn gear causing slippage under load
removed cover. Removed cover over gears. Used lock washer pliers to remove lock washer. Took out gears. Cleaned metal shavings from old gear and grease. Reassembled using new gear. Took about 15 minutes and saved $$ over sending mixer out for the repair.
Was this instruction helpful to you?
Thank you for voting!
Customer:
larry from northborough, MA
Parts Used:
WPW10731415
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Original Wire Whip had fallen apart,20 = years old
It took longer to remove from the box, Less than 10 seconds to install, push on shaft and quarter turn, that's it simple, now back to making homemade Marsh mellow covered in chocolate. New whip is sturdy and strong.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kathi from Roosevelt, UT
Parts Used:
W10807813
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
coating on beater coming off
took old off and new fit right in saved me over $300.00 for new mixer !
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the KG25H1XER5
106 - 120 of 195