KG25H1XER5 Whirlpool Mixer - Instructions

I am VERY impressed With this site . I am very disappointed with Kitchenaid. I paid more for this mixer than I paid for my first car especially when you ad in the attachments. I was mixing dough when I saw what looked like Small metal shavings in the dough... Then I heard a clacking sound so I turned off the machine and cussed...I got the screw driver and took off the top and was really surprised that on a machine that retails for over $550.00 dollars that the gear housing is PLASTIC...And this one had a crack down the side... So I took my trusty Phillips #2 and removed the housing to see that the front Bearing was broken as well so I got on line to kitchenaid and they are determined to continue the process of Shafting you and I with the prices of thier made to fail (Quickly) parts and lubricants.. Thank God for PartSelect. I got a better housing for half the money as well as a Bearing. Now I wish this were the end but remember I said that there was metal shavings in my dough? Well since I was going to have to replace the lube anyway I took apart the planetary gear as well and found that it had been shaving metal from the underside of the upper main housing .. After cleaning I checked and the lower bushing wasn't seated so it had been doing this since I bought it and I didn't know.. So I got a C Clamp and pressed it to where the thing should have been to begin with. If you are going to be working on the thing I suggest you tear it down completely and clean It thoroughly and inspect EVERYTHING closely... I have been eating metal shavings for who knows how long...

Took it apart, found stripped gears, a common problem. Reviewed parts diagram on your website. Got the parts, reviewed the diagram, removed defective parts, used retaining ring pliers. put it back together, put new grease in, tried it out. Very easy fix

I ordered the switch control. Opened up the top part of the mixer using a Philips screwdriver. Then I unscrewed all the screws that connected the old part. Disconnected the wires, connected them to the new panel , screwed everything back together and i was done. It was that easy.

I carefully removed the cover of my mixer. I first made sure that all of my part numbers corresponded, then I labeled the 5 wires that needed to be disconnected. I then disconnected the wires, removed the two screws holding the part in place, switched out the old for new, reconnected all of my wires. Mades sure everything looked tight, and put my cover back on. Works like a charm. I cried because what I really thought was going to be a $200+ fix, ended up costing me less than $50! And it was so easy.

I first ahd to remove the original feet by removing screws that held them in place. The new feet that I purchased were different then the original. They were a push in type and not held in by screws. I had to modify the base by drilling the foot holder to accept the new style feet. Once this was done, the feet were installed and looked good.

unscrewed the old one........screwed in the new one, no chance for electrocution or power tools..........darn!

Unplugged unit. Took top housing off of mixer (half dozen small screws). Disconnected speed control circuit card from five wiring connections. Removed card from mixer chassis (two screws). When new part came (the next day) I reversed the procedure in about 5 minutes and had a working mixer! Thanks.

Placed beater in mixer head.

Watched several videos on repair. Noted part placement while disassembling. Found problem, ordered and received parts. Cleaned out all old grease. Greased all parts and reassembled per recommendations, paying attention to the bearing race and washer placement. Firmly tensioned all fasteners, cleaned up and tested.

Removed 4 screws on mixer top. Removed 4 screws to gear box cover. Ordered replacement gears from Parts Select. Removed snap ring. Repaced two gears. Applied gear grease, replaced snap ring & screws. Gears at local appliance dealer were $39 each. Total parts from Parts Select + shipping under $20, received in 3 days!

Just twisted it in to place. Parts Select was awesome! Thank you!

removed cover annd snap ring removed gear and replaced with new,

This is the tightening screw that holds the attachments into the motor unit of the mixer. Found your web site and reordered 2 replacement pieces (in case one breaks!). Very EZ and user friendly. Thank you!

This was easy once Igot all the parts. The mxer wouldn't mix and when I opened it up the drive gear between the motor and the planetary drive was missing some teeth. Turns out the bearing, which was sintered bronze, had broken so I needed a new gear, new bearing, and the jumping gear had broken the housing so I needed a new housing. The new gearing ( really a bushing since there are no rollers or balls in the "bearing") waws now steel and the molded plastic housing is now cast metal. Some new grease ( I had to buy a quart can of grease to get two tablespooons) a new gasket and put the screws in and we're back in business. Total repair time 10 minutes, total time to get all the parts 3 weeks,

Researched the internet for a diagram of the mixer and used that to take it apart, clean everything, then install the new gear and new grease. Works great so far.