5KPM5CSM0 Whirlpool Mixer - Instructions

Unscrew and dismounted the mixer, gather all pieces and screws, cleaned and washed every part, took away the old grease and replaced it with a new one, also looked carefully for the lost teeth and found them, Put grease in every part, put back and screwed all the pieces of the mixer, then tried the mixer which worked really well.

My husband looked at youtube to figure out what the issue was. He saw a video that identified that the likely problem was the worm gear. My husband took the kitchenaid applicance apart, as he saw in the video. We ordered the part, it took less than a week to arrive. He rewatched the video that demonstrated how to put the kitchenaid mixer back together. It's a bit messy due to all the packing grease, but a pair of nitrile gloves, paper towels, and an old rag help. We put a garbage bag over the appliance after it was taken apart to protect it from any dust and my curious cat. We let the kitchenaid cycle for about a minute to make sure the gear was greased. I haven't used it to make bread yet, but I'll do that soon. Thanks for supplying the part that saved us at least one hundred dollars and TRY to get a person who will repair small appliances.

I discovered the brushes were worn, and one side had broken off and lodged against the armature.I got lucky as I removed the brush caps and the sleeves the brushes fit into (simple job) and was able to hand turn the armature so the pieces fell down into the bottom of the mixer housing.After removing them, I replaced the brushes and the mixer runs like new. Thanks for the fast delivery AND more importantly, the right part. Steve

Order part through parts select. it only took 3 days to receive part. The mixer was very easy to take apart and to replace the gear. it was back together in about 20 min. The video from kitchen aid to repair the unit is awsome. Thanks

I replaced the brushes. I didn't realize that I've put one of them wrong. Reminder for next time the brushes have to touch the rotor of the motor. It took me a little bit to understand but the brushes can go in and not touch the rotor. It works very quietly now. Thank you PartSelect for your infos and knowledge.

The knob was attached to the new lever. I began to disassemble the mixer case so that I could replace the lever. However, it soon became apparent that this would be a major project involving many components and potential problems in getting the unit back together. Since all I wanted was to replace the knob, I simply knocked it off the new lever and forced it onto the old one. It is hard for me to understand why Kitchenaid would not make just the knob available.

Opened beater , removed grease , took bearing off , removed alignment pins ,pulled shaft and pinion out , replaced parts , lubricated with new grease , assembled the whole drive . do not like the plastic gear or the clearance once assembled has a lot of slop for this type of drive .

I was very happy with the customer services department and the support I received in identifying the part I needed for the repair. I received an email confirming my order with all details. I do wish you had a more cost effective shipping alternative, like Priority mail.
The repair went well and the mixer is back in business, for making those Chocolate Chip Cookie and brownies if you know what I mean.

Thank you
Ron Ashby

Repair was easy. Remove the seal ring with a flat blade screwdriver and drive out retaining pin. Pry out lower unit using two screwdrivers, one on each side. Once apart, use spring clip pliers to remove snap ring. Pull out shaft and replace. Clean and lubricate as you reassemble in reverse. Google the model number to get detailed instructions.

The issue ended up being this little plastic clip. The repair took me about 20 mins alone to make. However, I realized how dirty the mixer was and spent another 30 - 40 mins detailing it.

Per a video on this site, I removed the stand part, then removed the rear electrical cover and aluminum band which wraps around the mixer. Next, remove the drip ring and planetary gear (use a punch). Then remove the 4 screws securing the bottom housing and the 5 screws around the planetary gear housing. You should be able to pull the upper and bottom housings apart now. This exposes the control lever. Just unscrew it and replace it. Re-install all parts in reverse order.

received parts promptly, opened motor removed three screws installed worm gear . installed brushes external access.Buttoned motor up and tested operation. Very esy to repair with the supplied [correct] parts

removed one screw from back cover, loosened two screws holding speed control plate, removed one wire at a time from old unit to new, screwed two top screws back on mixer,plug mixer back in, adjust speed control screws until I reached correct speed, put back cover back on

I dismantled the machine to find the problem and to see what part I needed. Than when I ordered the part I saw the video of how to do it. If I had seen the video before I dismantled, I would have save a few steps. The video was very complete and accurate even it being an older model

watched instruction video (from Part Select), the demonstration was close enough to enable me to repair the mixer. Newer mixers are disassembled differently.