KSM96MF0 Whirlpool Mixer - Instructions

With a screw driver remove the screws holding the old base in place. With a flat head screw driver carefully pry and remove old mixer base. With 600 grit sandpaper clean and make smooth any burrs or rough spots in the mixer base recessed area. You can use some light grease and coat the outer edges of new mixer base and place in the now cleaned mixer base recessed area. The new base maybe a tight fit and not be fully seated in the recess. If a tight fit, place the piece of 2x4 piece of wood over the new part that is in the recess and carefully tap the base home using the sledge hammer. Check to see, if the base is fully seated. If not fully seated, tap again When fully seated replace the screws. You may have to adjust the height of the stand mixer head with mixer paddle attached for proper clearance between bowl and paddle. See your mixer manual for adjustment procedure

Replaced gasket and O-ring. Problem solved. POC (Piece of Cake).

Removed the rear cover to inspect the speed board. Replaced motor brushes and noticed the motor body nuts were loose and 1 was completely off. Cleaned up speed board and replaced the motor body nuts, tightened with nutdriver, adjusted speedboard governor screws and with new motor brushes worked like a charm. The very rough sounding motor noise was gone and the mixer has not operated so quietly ever.

I took apart the mixer housing and removed all the screws. The most difficult part was the two pins that needed to be removed with a metal punch. They were in fairly tight. The mixer came apart pretty easily and it was obvious which part needed to be replaced as it was broken and missing teeth. After replacing the gear and applying new grease for smooth operation, I simply put it back together and it has worked like new ever since.

Dismantled the mixer, took photos, and re-assembled unit.

I watched the university of YouTube videos, and followed their instructions.

INSTALLED PHASE CONTROL BOARD AND SPEED CONTROL PLATE, BOTH AT SAME TIME
Your DYI video was helpful, especially holding the spring with a cloth. Also good for fine tuning to get the speed exact

Took each area apart. Replaced the gear and reassembled it.

watched how to repair

Used youtube movies to disassemble the mixer and found that the gear was stripped. I kept the screws in labeled ziploc baggies so I wouldn't forget which screws went where. Once the part arrived, it was very simple to replace the gear. I regreased the mixer and then reassembled. The trickiest part was how greasy everything was! It was also hard to get the pin through the beater hub - I found a video that suggested using a very slim screwdriver to thread the hole before inserting the pin. This was the most involved part replacement I've done on my own, and it was very satisfying to get my mixer back in working order!

had to replace the outlet strip and relocate the mounting screw,,,,wiring cord to the mixer was super correct and had to simply follow basic wiring (black to black,,,silver to silver,,,green to ground) ,,, the cord came with the correct mounting bushing already on the cord. Thx a bunch!

I had a sourdough batch get into the space where dough hook attaches and it got so stuck that nothing - not hot water baths, not pliers and screwdrivers got the dough hook released. I had to open up the mixer following partselect you tube instructions and replacing the parts. What was confusing to me at first is that my 45 year old mixer had an extra screw on top of the shaft that no longer is there for newer models. It took me longer than I am willing to admit to figure that the extra screw is not the result of me skimming the instructions - the original shaft and dough hook went to a friend who broke it attempting to disengage the two parts (the dough turned out to be a very strong form of glue!). The piece is working like new. I preferred the agitator shaft with a spring to hold the end piece tighter, but the new set up without a spring works just fine.

The new part was too large for the replacement job, but we used the self tapping screws that came with the mixer and screwed them in from the bottom to open the holes a little more since the original screws were to short to hold the new plate. Then we replaced the screws with longer screws and that seemed to do the trick!

Removed back cover, disconnected the 2 push-on connectors, removed ground wire screw. Reversed the process to install new cord.

Followed your instructions from the internet and it was a simple fix. Mixer works great again. Thank You ..you made it easy!