5KSM185PSBAZ4 Whirlpool Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Linda from St. Cloud, WI
- Parts Used:
- WP116287
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed new brushes for a mixer
Easy to locate part I needed (brushes)..great diagrams Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- andrew from bridgeville, PA
- Parts Used:
- WPW10380496, W11656718
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
would not run
I just put in the new brushes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Aitkin, MN
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Screw cap or retainer wore out and wouldn't hold the bowl tight
Removed the old screw cap and installed the new one-only has 3 screw to remove and re install. VERY easy. Fits perfectly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Tolland, CT
- Parts Used:
- WPW10112253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Sticky back disc on Orbital sander came apart (from old age )
remove 3 screws ,remove old sanding disc replace with new installl screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from Fairfax, VA
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Mixer bowl was slipping off the base when in use
Replacing the base retaining bracket(what KitchenAid calls the screw cap) solved the problem immediately. The entire replacement effort took no more than a minute requiring removing 3 screws, discarding the old base, putting in the new one, and putting the screws back in. PartSelect was very easy to do business with. They shipped the part the day I ordered it and it arrived as scheduled. Can't be easier than that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tiffany from San Antonio, TX
- Parts Used:
- WP16910
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Pin fell out of neck
Placed pin in the hole...some wiggling had to be done for a tight fit. Installation complete!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nick from Naperville, IL
- Parts Used:
- WPW10380496
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
My wife was complaining of a loud grinding noise.
I replaced the brushes. I didn't realize that I've put one of them wrong. Reminder for next time the brushes have to touch the rotor of the motor. It took me a little bit to understand but the brushes can go in and not touch the rotor. It works very quietly now. Thank you PartSelect for your infos and knowledge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CONRADT from El Paso, TX
- Parts Used:
- WPW10323373, WPW10112253, WP240210-2, W11082541, WP4162324
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Stripped plastic gearr
Opened beater , removed grease , took bearing off , removed alignment pins ,pulled shaft and pinion out , replaced parts , lubricated with new grease , assembled the whole drive . do not like the plastic gear or the clearance once assembled has a lot of slop for this type of drive .
Was this instruction helpful to you?
Thank you for voting!
Replaced main gears
1. Removed the mixer from the base by removeing the pivot pin at the mixer base support. 2. removed the retainer ring from the housing. 3. removed the pin from the shaft. 4. removed 5 philips machine screws from the round base. 5. removed the round base from the mixer housing. 6. removed the o-ring from the shaft. 7. removed the shaft and large worm/pinion gear from the shaft. 8. pressed out the pinion drive gear from the mixer. The reverse operation repaired the mixer to new condition.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alvaro from Brighton, CO
- Parts Used:
- WP240309-2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Worm gear was bad
Order part through parts select. it only took 3 days to receive part. The mixer was very easy to take apart and to replace the gear. it was back together in about 20 min. The video from kitchen aid to repair the unit is awsome. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stephen from indianapolis, IN
- Parts Used:
- WPW10380496
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Mixer quit running
I discovered the brushes were worn, and one side had broken off and lodged against the armature.I got lucky as I removed the brush caps and the sleeves the brushes fit into (simple job) and was able to hand turn the armature so the pieces fell down into the bottom of the mixer housing.After removing them, I replaced the brushes and the mixer runs like new. Thanks for the fast delivery AND more importantly, the right part. Steve
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from dahlonega, GA
- Parts Used:
- WPW10112253, W11082541
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Worn Worm gear
I took out the worm gear and replaced it with the new one. It is important to have the correct punches that are just under the diameter of the pins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from Ledyard, CT
- Parts Used:
- WP243368
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Worn spring would not allow atthing mixer attacments
Repair was easy. Remove the seal ring with a flat blade screwdriver and drive out retaining pin. Pry out lower unit using two screwdrivers, one on each side. Once apart, use spring clip pliers to remove snap ring. Pull out shaft and replace. Clean and lubricate as you reassemble in reverse. Google the model number to get detailed instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Rehoboth Beach, DE
- Parts Used:
- WPW10380496
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
motor brushes worn out
Neither motor brush popped out with the spring as shown on videos. Both appear to have disintegrated in part and had to be chiseled out delicately using and ice pick and tapping gently with a hammer. This left a carbon powder and pieces of the old brushes on the counter. Inserting the new brushes was as easy as shown on the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dallas from Atlanta, GA
- Parts Used:
- WPW10112253
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Broken worm gear
Knob fell out of the front of the mixer into the bowl and jammed the beater. This caused the motor to strip the plastic worm gear. Open unit to investigate and found about 4 teeth missing out of the worm gear. Ordered a replacement. Installed the new gear once received in about 30 minutes. Wife is now happy again. Just need to make sure you pack enough gease into the new gear before reassembling the unit.
Was this instruction helpful to you?
Thank you for voting!