KD2661KATRW KitchenAid Mixer - Instructions

First and foremost, I am not mechanical at all. I typically refer to parts as thing-a-ma-jigs, and whatca-ma-call-its. When it froze up and started to make a loud grinding noise, I guessed it was a gear problem. I decided to try to take it apart, What did I have to lose? If I couldn't figure it out, I would be down a mixer. I was already down one as it was. It was very easy to take apart and I could immediately see what gears needed to be replaced. Parts Select made it very easy to see what parts I needed. And delivery was lightning fast; the next day after it shipped! I found a PDF on line on how to dis-assemble and re-assemble the mixer. I got it together and it mixed for a few minutes and froze again. I took it apart and realized that I didn't have the whatcha-ma-call-it (worm gear) seated properly. Fixed it and put it back together and put it to the test. Working just fine now! Thank you Parts Select for making this very easy!

This is a 6 Qt. made by Kitchen Aid Stand Up mixer 575. watts with 6 qt. bowl. A powerful machine. But not geared to crush Almonds. After about 2 quarts of Almond crushing to make Almond butter I heard the machine thumbing inside and turned it off immediately. Mind you, I am a 60 year old man with Maintenance Mechanic, and Machinist skills. If you listen to my instructions which aren't that hard you can do this. REMOVE THE POWER CHORD BEFORE CONTINUING. First you have to find the screws that hold the top half of the machine together. They are under the silver Kitchen Aid Stainless Steel 5/8th Band that runs around the middle of the machine. On the back of the machine is a small machine screw that when taken out removes the band. Remove the band carefully as not to bend it because it has to go back on looking pretty. Comes off easy. You will then see 4 longer 3/4 inch screws around the middle of the machine head. When you remove these screws the top half of the machine head will lift up. The top half of the machine head lifts off very easy. Throw all your screws into the top so you don't mis place them. You will see a Motor some gears on the side and a shaft that comes from the motor going into a Cast Aluminum Casing with another 4 screws 3/4 exactly the same size as the ones you took from around the top mixer casing. This is easy cause you don't have allot of different size screws only the one small one that screws on the back of the band. After these four screws are removed, again lift up the top half of the casing but this time it will be full with gear grease. Put the casing aside and using paper towels wife a little of the gear grease off the top gear. In order to turn the gear you must use the side drive gear or look around the gear you will notice in some of the gear slots will be shinny and worn. This is the Bevel Gear. There is a C locking shaft cliff that keeps the gear locked in. You must have a multiple C clip remover pliers that has different size C clips for the holes in the clip must be spread apart in order to remove the clip all the way up the shaft. NOTE:; DO NOT USE A PLYERS TO TRY AND PRY THIS CLIP OFF IT IS STRANG AND YOU MAY MAR THE STAINLESS STEEL GEAR SHAFT. You must use the gear C clip remover, I found one moderately prized for 25 dollars at the Home Depot or any large chain hard ware stores will have it. After the C clip is removed, slide the gear evenly up. If it's stuck that's only because of grease unless you mar the shaft by not listening to me. I also replace the Top Hum Bevel gear which is in the top half of the hub. Parts select has a Diagram that shows you the parts and where they are. When putting on the Bevel Gear over the shaft be sure to lower it evenly and guide it onto the worm gear. There is a small pin that sticks out in the middle of the gear make sure this lines up when setting the gear into the worm gear. The Top Bevel Gear, falls right out and you can use your figures to pull this one out and put the new one in. If you replace the Bevel gear my experience as a mechanics is to always replaces the adjacent gear as well, both will be worn. attach the C cliff the same what as taking it off except opposite. Pull the tow clip holes apart and slide it down to the shaft groove for the clip. Put everything back the way you took it off. One NOTE;.. DO NOT DO TOUGHT THE SIDE DRIVE GEAR IT IS SET IN WITH BRASE LOCKING SHIMS AND HAVE TO BE SET A CERTAIN WAY TO CLOSE. When closing make sure the Top Hub is in line with these brace shims. After screwing the hub back down do not over tighten, just snug it tight. Be sure to buy axle gear grade and replace any grease removed, this chamber must be loaded with grease. There is never too much only too little as you will wear the gears down without the proper amount. DO NOT TOUCH ANY THING THAT DOES NEED TO BE TOUCHED LIKE THE MOTOR OR DRIVE SHAFTS OR SIDE MAIN GEAR…

I sent for a new thumb screw and screwed it in where it belongs and now I can use my other attachments.

replaced Speed control board. less than 40.00 took ten minuets from the time I started until we were making cookies.

opened the mixer.. all screws in kitchaid are the same so not to worry... opened up and replaced the gears... and put it back together... diagram helped in that front and rear bearings of connecting gear are the same # on diagram it is easy to confuse when you put it back together, but the item number and description of each helped make sure it was in the right place. Otherwise... time to fix would have been less....

took mixer cover off, took gear box cover off, removed gears, replaced gears, replaced covers, made cookies, no problem!!

Remove the top cover , inspect the gears . In my case the worm gear and the gear follower worn out . I removed the damage gears and the old grease , clean the inside and reinstalled everything . Now , the mixer is working good again.

removed top casing, removed old switch and sensor,and replaced with new ones. It was just a matter of a half dozen screws and unpluging 4 or 5 wires and then reversing the process. Couldn't be easier. thank you

Removing the cover of the mixers "guts", it was immediate evident the a major gear had lost a few of its "teeth". Parts Select clearly offered the required part of this $300 mixer for a favorable price. I was fully impressed that it arrived within 4 days or my ordering the part. I simply exchanged the damaged gear and restored the mixer to service and I'm fully impressed with the Parts Select Company for their swift response to my needs.

remove the cover,take out four screw from gear box,remove the gear box,clean all gears,then you see damage gear,replace it ,install new grease.

Looked at the schematic for this model on Parts Select. Removed Aluminum band screw, removed the 4 screws that hold the top of the mixer. Lifted the top off. Removed 4 screws and lifted the gear case. Removed snap ring and took off tapered gear. Removed pin and removed worm gear. Picked out the metal, in the grease, from the old worm gear, using a magnet then inserted new worm gear and put it back together in reverse order. There was plenty of grease and didn't need to add any.

Took housing off, removed computer board and disconnected speed control assembly from board. Soaked plastic slide in hot water and freed up mech. Discovered a crack in plastic slide from forcing it. Ordered new assembly and installed. TIP: Keep slide clean of substances that will jam it by cleaning occasionally with water. For a complete cleaning you will have to remove it. Total of 6 easy to reach screws.

Took mixer apart and then the gear compartment. inspected components. Replaced the worn gears and re-greased the new parts. Put the gear compartment back together, tested the operation of the unit and then replaced the rest of mixer, re-tested and declared victory.

the plastic covering the thumb screw cracked almost half way and lost the piece....so the new one is being used to replace this old one...very easy to install

removed cover. Removed cover over gears. Used lock washer pliers to remove lock washer. Took out gears. Cleaned metal shavings from old gear and grease. Reassembled using new gear. Took about 15 minutes and saved $$ over sending mixer out for the repair.