KSM500Q2TG0 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mariette from VALPARAISO, NE
- Parts Used:
- WP3182857
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken spring latch
Unscrew the broken latch; remove it; screw in the new latch. Very, very, very easy to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ethan from MEADVILLE, PA
- Parts Used:
- W11805888, WP240309-2
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Damaged gears in both machines. Been setting around for a few years broken. Gears broke way too soon.
Simply removed damaged gears. Very simple to do. Ordered gears. Replaced gears. Both working well ( so far. ) Machines are easy to dismantle. Just be sure to put the screws back in the holes you took them out of when dismantling...no lost screws. On the smaller model, took pictures of the wire positions to be sure they were replaced in the proper order. Larger model had no wires to remove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from CISCO, GA
- Parts Used:
- WP240309-2
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
worm gear worn out
I watched a short video on replacing the worm gear, although I did not know what the problem was until I watched the video. after the video ended I took the mixer apart and found the problem located a parts number an placed my order. got the part in one week put in the new part in about 20 minutes and it work like new. and the price was very reasonable
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from LEXINGTON, SC
- Parts Used:
- W11312468
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Splash from K45 KitchenAid Mixer Bowl
The shield works sufficiently. Note that the shield is not a continuous circle as shown in the picture. This actually can be an asset because it can be installed or disassembled without stopping the mixer of having to lift the head while running.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marcia from NEW YORK, NY
- Parts Used:
- WP3182857
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Spring latch snapped off making bowl unstable and unless hand stabilized wobbled too much to use.
SO SIMPLE!!!!! Using a regular screwdriver, remove the remains of the Spring Latch. Place new one over holes and screw new one in place using the currently used screws. May wash off screws first if caked with gunk. OMG!!! TOOOO easy and saved me from throwing out a very terrific 40 year old PRO LINE KITCHEN AID MIXER!! To replace it would have been hundreds of dollars.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from GLEN ALLEN, VA
- Parts Used:
- WP3182857
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
spring latch was broken
changed the part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sabrina from BUNKIE, LA
- Parts Used:
- WPW10380496
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burnt brushes
The brushes are located on each side of the tilt head of the mixer. I used a screwdriver to remove the screws, removed the brushes & replaced with the new ones. Runs great again!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ely from Monsey, NY
- Parts Used:
- WP3182857
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bowl shaking during use
line up the screw holes and screw it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from JACKSONVILLE, FL
- Parts Used:
- WPW10325124
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Mixer went to high speed immediately on starting
Simple fix actually. UNPLUG mixer and remove the one screw on top that holds on the back. The Phase control board sits under and behind the paper insulator and "switch" assy. Remove the 4 wires with a pair of needle nose pliers, the one screw holding it to the back of the mixer and install the new one in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GALO from DECATUR, GA
- Parts Used:
- WPW10325124
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Mixer operarates at high speed only.
Removed old one and replaced with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BRIAN from PALISADE, CO
- Parts Used:
- WPW10112253, W11192794, W11805888
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Decorative plug at top of mixer fell into the bowl and jammed the mixer stripping gears
Watch U Tube video. Take care to keep track of disassembly. Hard part was to have 4 types of screw drivers to fit the different screw heads. Be sure to clean broken gear clogs out of the grease. Parts select lady was a great help. Download Parts select diagram for extra help. Time and patience!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rachael from SEATTLE, WA
- Parts Used:
- WPW10112253
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
Worm gear was stripped and needed to be replaced
I am not handy, but was able to follow this YouTube video and do this repair easily and successfully: https://www.youtube.com/watch?v=1QsgPIL9FpA
I did take the mixer apart first to verify that the worm gear was the issue, then ordered the part from you site. I received it quickly and was able to do the repair and get back to mixing in a few days!
I did take the mixer apart first to verify that the worm gear was the issue, then ordered the part from you site. I received it quickly and was able to do the repair and get back to mixing in a few days!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steve from OWASSO, OK
- Parts Used:
- W11192794, WP67500-55, 4160474
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Mixer was making a loud noise and the attachment port was not working
Watched a couple of youtube videos and it was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from CEDAR CITY, UT
- Parts Used:
- WPW10112253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Plastic worm gear gave way (as designed) when the grain mill over-worked it.
I did exactly what the PartSelect video demonstrated after watching other DIY videos on the Internet, thus I did not remove the stand which seemed like a little too much for a simple straight forward repair. This is the second time I have replaced this gear. The first time was about 10 years ago when the bakelite gear broke on a 30 year old KitchenAid K
-45. That mixer made hundreds of loaves of bread after grinding many pounds of wheat berries. The only reason we had to replace it was that it walked off the flour dusted counter and landed on its head when my wife had her back turned. Otherwise we would still be using it. :-)
Thanks for the excellent service and instructions.
-45. That mixer made hundreds of loaves of bread after grinding many pounds of wheat berries. The only reason we had to replace it was that it walked off the flour dusted counter and landed on its head when my wife had her back turned. Otherwise we would still be using it. :-)
Thanks for the excellent service and instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angel from JACKSONVILLE, FL
- Parts Used:
- WPW10380496
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Won't Run
Found control backplate out of adjustment. Should be nominal 3/8".Broken speed control spring which attaches to backplate bottom.
I recommend Loctite Blue to complement locknut's when adjusting RPM of "Stir" speed
I recommend Loctite Blue to complement locknut's when adjusting RPM of "Stir" speed
Was this instruction helpful to you?
Thank you for voting!