3KSM5CBTER0 KitchenAid Mixer - Instructions

Was able to use the diagrams to figure out how to put everything back together. Would have been a nightmare without that as I took the thing apart without really paying attention to what went where. The hardest part was inserting a set pin that holds the Bowl lift arm, which fits inside the stand. in place. So new parts - $20, less than an hour of my time disassembling/reassembling, probably saved me $125 in repair plus a couple hours driving it to service place and picking it up. No brainer.

Follow a YouTube video step by step

watched an internet video to see what to do. Unfortunately even after replacing the chip the mixer it still didn't work.

disassembled replaced part reassembled now works well

I removed the spring loaded brush screw on the side of my mixer and lost it the next day. I found a schematic of this part on your website and ordered the four pieces that make up the brush screw(?). They arrived in just a few days and I referred back to the schematic to put it together. I then popped it in my mixer, screwed it down, plugged her in and away we go! Easiest repair I’ve ever done! I’m a 70 year old retired lady and not very handy, but this was an easy fix! Thank you, PartSelect!

First of all I found the part in no time flat and ordered it early afternoon and it was at my door within 24 hours! My son was off work one day and I asked him if he needed a job to do and he said "sure". So I showed him the new part and where it goes and in less then 10 min it was working. awesome!

Skewer the screw in with my fingers,

Used the diagram on the website and a video
Totally worked!

i disassembled the mixer until i could remove the worm gear; is in a housing that that includes another gear and shaft. make sure you have a magnetic tray to put parts in as you work or you will spend more time looking for parts than reassembling the mixer. once you have the gear housing out you will need a small diameter punch to drive out the pin that holds the gears in the housing(i used a 5/32 transfer punch.) make sure you punch the pin out where it will be caught or you will need to order that part because you will not find it. after knocking the pin out it is just a matter of removing the old gear, putting the new one in, and reversing the steps and getting everything reassembled.

While kneading dough, my 27-yo stand mixer walked off the counter, and shortly thereafter the plastic bowl lift arm piece broke. After a quick internet search I ordered the part. Installation was extremely easy. 1) Using a rachet with a #3 Phillips head bit, remove the four screws holding the motor to the base. 2) Using the Roll Pin Punch pop out the roll pin. 3) Loosen and remove the cotter pin with the screwdriver and pliers. 4) Remove the broken piece. 5) Attach the replacement piece to the handle and insert the roll pin, tapping into place with the Roll Pin Punch. 5) Attach the lift arm to the piece and fix with the cotter pin. 6) Reattach the motor to the base. Ready for 27 more years of stand mixing duty!

Removed the two screws that hold the bowl spring in place. Removed broken spring. Replaced broken spring with replacement spring. Tightened two screws that hold it in place.

I just thought there had to be a way to replace a component to correct the speed problem. I've never worked on a mixer before, so I thought it would be a challenge. Actually the repair was fairly easy. Make sure the unit is unplugged from AC. I removed the back motor cover with one screw and removed the end seal. I compared the parts on the mixer with the diagram provided at the Part Select website. I then ordered the parts. When the parts arrived 3 days later, I removed the Speed Control Plate ( 3 screws) and Phase Control Bd (1 screw) as one Assy. Removed the old Governor and slipped on the new one. Assy the new Speed Control Plate and Phase Control Bd comparing wiring and screwed them back to the unit. Removed the two motor bushes by unscrewing the side black motor brush holders and inserting the new brushes. I tried powering motor and nothing happened. I thought, great, now what did I do? I found out that you must make sure the brushes actually touch the armature otherwise the motor doesn't run. The gears are worn from grinding to much deer meat and my wife says no more. I've ordered new gears and looks like that job, too, will be easy to repair. Adding these parts is alot cheaper than buying a new unit and it will run like new. Not bad for over 10 years of usage.

I screwed the two screws into the place of original holes and Voila! it was repaired.

removed old screws and latch, replaced it with the new. took just a few seconds. This is the first time i ever fixed anything. customer service was amazing

disasembled found stripped gesr assembly ordered and replaced went very smoothly. It would have been good to have info and acsess to the correct gear grease to use in a mixer / food grade but it worked out well anyway.shipping was very fast thanks