Models > 4KN15C1XWH1 > Instructions

4KN15C1XWH1 KitchenAid Mixer - Instructions

Jump to:

All Instructions for the 4KN15C1XWH1
91 - 105 of 226
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Jamie from Jamestown, ND
Parts Used:
W11086780
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
gear teeth worn off worm gear
replace worm gear
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jerry from Southport, NC
Parts Used:
WP9709231, W11086780
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Worm gear stripped.
Remove covers, open gear box, remove lock ring and gears to deterime which gears were bad. Remove old grease, install new gears and pack with new grease.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mike from DEFIANCE, OH
Parts Used:
W11086780, WP9709511
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Worn gear
Remover screws from top. Used snap ring pliers to remove snap ring replaced gear and reassemblied.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Thomas from LILBURN, GA
Parts Used:
WP9706648
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Bad speed control
Thank goodness for YouTube. Pretty much followed the process of taking it out. Was easy, but having a video made it a bit simpler.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mark from LEXINGTON, SC
Parts Used:
W11312468
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Splash from K45 KitchenAid Mixer Bowl
The shield works sufficiently. Note that the shield is not a continuous circle as shown in the picture. This actually can be an asset because it can be installed or disassembled without stopping the mixer of having to lift the head while running.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from Harrodsburg, KY
Parts Used:
WP9706648
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers
Speed switch bad and Initially thought new part was wrong!
At first thought part was incorrect as the electrical connection tabs on the circuit board were not inline as the existing part. However, upon closer examination I realized that the same quantity of tabs existed on the new part and although not inline, were clearly marked the same as the original part. Unit was easily replaced and is operating just like new.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
FRANCISCO from SAN BENITO, TX
Parts Used:
WP9706648
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
REPLACE SPEED CONTROL SWITCH
REPLACE SPPED CONTROL SWITCH
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Russell from NEW LONDON, CT
Parts Used:
8212396
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
The stand mixer would not rotate at low speed. Upon disassembly found one of the two alignment pins of the upper gear case broken.
1. Removed the decorative band then the upper motor cover.
2. Removed the upper gear case cover. Found one of the two alignment pins broken.
3. Inspected gears.
4. Cleaned out old grease.
5. Repacked with new food grade grease.
6. Reassembled.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from ST AUGUSTINE, FL
Parts Used:
W11192795, 8212396
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
attachment planetary gears stripped
removed top housing, removed gear housing cover, removed all gears, cleaned out all grease, obtained gears and new housing cover, fit all gears in housing, filled with grease and put on housing cover.
Reassembled mixer.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Karl from Hammond Ranch, CA
Parts Used:
W11192795, W11086780, WP9707223, WP16897
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set, Wrench set
Planetary Pinion Gear Assembly had dropped down
The repair was easy, I only had to order new gear assembly parts and to replace the associated worn parts (shaft, pin, and gears).
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from CEDAR CREEK, TX
Parts Used:
8212396
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Broken gear case.
Remove and replace gear case. Apply food grade grease secure with screws.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bruce from EUREKA, CA
Parts Used:
W11086780, WP9703445, WP16897
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Bad control switch, striped worm follower gear.
Removed 2 screws holding the switch unplugged the one at a time.
opened the gear box cover 4 Philip screws, cleaned out the grease
removed the pinion gear, removed pin, removed the planet gear assembly replaced gears in reversed order greased it up put gear cover back on and tested worked great.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
EBEN from WEST PALM BCH, FL
Parts Used:
WP9706648
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
unit would only operate at high speed
using Phillips screw driver, remove 5 screws - take off cowl (cover)l. remove 2 screws holding speed control assembly
unplug old speed control assembly (4 plugs) and plug in new speed control unit - reassemble cowl .
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
cosimo from EL CERRITO, CA
Parts Used:
WP9709511, WP9703445
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Socket set
I stripped a couple of gears due with a batch of very hard dough
Taking apart the machine is really easy. I was worried the grease would have spilled all over the places, but when the machine is cool, the grease is solid, so no spill. Replace the parts is quite straightforward, and there are plenty of tutorials on line. The only tip is that the grease used by KitchenAid is dark, and it is not easy to see all the small parts when you take the gearbox apart, so pay attention at what you do and at what you throw away... when I got to put it back together I missed a special concave washer which must have been trapped in the grease. Other than that... it has been an easy repair, the mixer is back up and running and I saved a ton on $$$
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Stuart from Pittsford, NY
Parts Used:
W11086780
Difficulty Level:
Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Gear Stripped was trying to replace
Could not get it properly installed. Had to take to a repair center for completion.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 4KN15C1XWH1
91 - 105 of 226