KSM500QBF0 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- john from North Kingstown, RI
- Parts Used:
- WP3182857
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Spring latch on Kitchenaid broke
Two flat head screws removed, swapped out the latch, and replaced.
The entire repair took about two minutes.
Price was acceptable given the worth of the mixer.
The entire repair took about two minutes.
Price was acceptable given the worth of the mixer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Wewahitchka, FL
- Parts Used:
- WPW10112253, WP9705444
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
mixer would not turn
removed the screws holding the mixer housing and then removed the worn worm gear by removing the roll pin holding it on the shaft. Replaced the worm gear and inserted the pin that hole it in place. Replaced some of the gear grease and reassembled mixer. Went very easily. No problems at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alice from St Louis, MO
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plastic boke on the old thumb screw
unscrewed the old one........screwed in the new one, no chance for electrocution or power tools..........darn!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from FREEPORT, TX
- Parts Used:
- WPW10330804, WPW10325124, WPW10119326
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
use your phones to take pic of how the wiring is to be reconnected, take pleanty from all angles
repair is farly simple just take your time, First attempted i didnt replace the speed covernor looked ok but had problems getting slow end to work properly decided to go ahead and install since i purchased it also and walia took care of the cogging problem. Good Luck
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from CUBA, NY
- Parts Used:
- W11557271, WPW10119326, WP9709276
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Speed switch wouldn’t stay in off position
Watched a YouTube video to disassemble,from there went smoothly. One small piece of advice,take pictures with your smart phone during the process. Makes remembering easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from CAPE CORAL, FL
- Parts Used:
- W11557271, WPW10119326
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
The speed linkage was broken inside the mixer.
Literally the whole top of this stand mixer had to be taken apart. With the help of U-tube! We realized the silver strip was removable and there where screws underneath. We figured we would replace both parts while it was all taken apart. We cleaned the mixer and added some grease where necessary. I now have a 25 year old new mixer. Thanks for having our parts and guiding us with a diagram of the unit. Very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from OXFORD, MI
- Parts Used:
- WPW10112253, WP4162324
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
worm gear stripped
Looked for the probable cause from a U-tube video, then found the parts list and repair video on the PartSelect website. When the parts arrived within 3days the shipped email had a video on exactly how to complete the repair. Repair video was very well done and easy to follow.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kate from BELLINGHAM, WA
- Parts Used:
- WP4162324, WP240309-2
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The smallest gear was broken, so we got the worm gear and bracket as well as a new gasket and some lube to grease the gears
We disassembled it with the help of a YouTube video from partselect.
We saw the damaged gear, removed the 4 screws to remove it, cleaned all the old grease out with rags so it wouldn't be contaminated by metal shavings.
We reassembled it per the YouTube video and it works better than ever!!
Make sure you remove the roll pin before trying to pry off the planetary plate, because I watched a different video first, which didnt tell me that and i bent it a bit.
We saw the damaged gear, removed the 4 screws to remove it, cleaned all the old grease out with rags so it wouldn't be contaminated by metal shavings.
We reassembled it per the YouTube video and it works better than ever!!
Make sure you remove the roll pin before trying to pry off the planetary plate, because I watched a different video first, which didnt tell me that and i bent it a bit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosemary from Gaithersburg, MD
- Parts Used:
- WPW10731415
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bent the original wire wisk
Just twisted it in to place. Parts Select was awesome! Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peggy from Escondido, CA
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
plastic outer casing on tightening screw had broken
This is the tightening screw that holds the attachments into the motor unit of the mixer. Found your web site and reordered 2 replacement pieces (in case one breaks!). Very EZ and user friendly. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from COLUMBIA, NJ
- Parts Used:
- WP9705444
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Pin was missing therefore no mixing function
Place Pin in hole where it was missing then gently tap pin into place
Run a test and all is good ??
make sure to use a drift pin set
Tom
Run a test and all is good ??
make sure to use a drift pin set
Tom
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EUGENIO from MIAMI, FL
- Parts Used:
- W11192794
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
spent Pevel Pinion Center Gear
remove the back cover part # 36, remove the top cover part # 1 (by removing the chrome ring parate # 28, the mobile disk part # 25 and six screws part # 24). This done, remove the system parat # 38 to release the Pevel Pinion Center Gear part # 15 and remove the damaged part and put the new part. The install the removed parts in reverse order as they withdrew.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beth from Torrington, CT
- Parts Used:
- WP241764
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Bowl won't lift
A part required to operate the bowl lift had failed, "broken in half". I removed the base, by removing 4 large philips head screws, then removed the pedestal which housed the broken part by removing 4 more large philips head screws. I used a hammer and punch to drive out the split pin, a pair of pliers to remove the cotter pin and replaced the broken part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from MARTINEZ, CA
- Parts Used:
- WPW10330804, WPW10325124, WPW10119326
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Mixer would not turn on
Pulled off end cover. Used the how-to video's to show me how to remove the (3) components (watch out when it comes to removing the spring). Removed all (3) components (one issue was the black cardboard seal, which because of its age broke. Hindsight tells me that I should have purchased a replacement seal along with the (3) new parts.
Fixed the broken part of the seal with scotch tape). Installed all new parts with the help of the video's and put the cover back on. Even with the new parts, the mixer would not run. Come to find out, after I took it to an appliance repair person, that someone had pulled both brushes and put them back in improperly. I could not find a how-to video that showed me how to de-install/re-install the brushes properly. I assume that was because new brushes were no longer available for purchase. At any rate, when the brushes were put in properly, everything worked. The repair person also adjusted the (2) screws on the speed control plate so that when you change the speeds via the lever, it all works properly. I didn't find a how-to video covering those adjustments either.
Fixed the broken part of the seal with scotch tape). Installed all new parts with the help of the video's and put the cover back on. Even with the new parts, the mixer would not run. Come to find out, after I took it to an appliance repair person, that someone had pulled both brushes and put them back in improperly. I could not find a how-to video that showed me how to de-install/re-install the brushes properly. I assume that was because new brushes were no longer available for purchase. At any rate, when the brushes were put in properly, everything worked. The repair person also adjusted the (2) screws on the speed control plate so that when you change the speeds via the lever, it all works properly. I didn't find a how-to video covering those adjustments either.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Petersburg, MI
- Parts Used:
- WP240775-1, WP240253-1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
End seal broken and Cover tabs broken.
Unplugged mixer. Removed screw holding cover on. Removed end seal. Inspected repair area for furhter damage. Installed new end seal and cover.
Was this instruction helpful to you?
Thank you for voting!