K4SSWH0 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jack from GLEN ALLEN, VA
- Parts Used:
- WP3182857
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
spring latch was broken
changed the part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sabrina from BUNKIE, LA
- Parts Used:
- WPW10380496
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burnt brushes
The brushes are located on each side of the tilt head of the mixer. I used a screwdriver to remove the screws, removed the brushes & replaced with the new ones. Runs great again!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from JACKSONVILLE, FL
- Parts Used:
- WPW10325124
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Mixer went to high speed immediately on starting
Simple fix actually. UNPLUG mixer and remove the one screw on top that holds on the back. The Phase control board sits under and behind the paper insulator and "switch" assy. Remove the 4 wires with a pair of needle nose pliers, the one screw holding it to the back of the mixer and install the new one in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dustin from JACKSONVILLE, NC
- Parts Used:
- WPW10112253
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The mixer broke the worm gear(the only plastic gear inside the mixer) and needed replaced.
I took apart the mixer housing and removed all the screws. The most difficult part was the two pins that needed to be removed with a metal punch. They were in fairly tight. The mixer came apart pretty easily and it was obvious which part needed to be replaced as it was broken and missing teeth. After replacing the gear and applying new grease for smooth operation, I simply put it back together and it has worked like new ever since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from HUNTINGTON, IN
- Parts Used:
- WP240309-2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Worn Worm gear. Mixer made a clunking noise and wouldn't turn.
Followed your instructions from the internet and it was a simple fix. Mixer works great again. Thank You ..you made it easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from CISCO, GA
- Parts Used:
- WP240309-2
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
worm gear worn out
I watched a short video on replacing the worm gear, although I did not know what the problem was until I watched the video. after the video ended I took the mixer apart and found the problem located a parts number an placed my order. got the part in one week put in the new part in about 20 minutes and it work like new. and the price was very reasonable
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GALO from DECATUR, GA
- Parts Used:
- WPW10325124
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Mixer operarates at high speed only.
Removed old one and replaced with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from OSSINEKE, MI
- Parts Used:
- WPW10325124
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Control stuck in high gear.
With the mixer being over 30 years old we believed it has going to have to be replaced. However, my husband jumped on uTube and looked at reviews for the problem. Motor was only running on high speed. Reviews said to replace the phase control board. Repair was very quick by just taking off the cover. Removing the old board and connecting the new. Mixer is working awesome once again. In such a disposable society it is great to be able to fix vs trash. Happy Baker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ely from Monsey, NY
- Parts Used:
- WP3182857
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bowl shaking during use
line up the screw holes and screw it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mariette from VALPARAISO, NE
- Parts Used:
- WP3182857
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken spring latch
Unscrew the broken latch; remove it; screw in the new latch. Very, very, very easy to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marcia from NEW YORK, NY
- Parts Used:
- WP3182857
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Spring latch snapped off making bowl unstable and unless hand stabilized wobbled too much to use.
SO SIMPLE!!!!! Using a regular screwdriver, remove the remains of the Spring Latch. Place new one over holes and screw new one in place using the currently used screws. May wash off screws first if caked with gunk. OMG!!! TOOOO easy and saved me from throwing out a very terrific 40 year old PRO LINE KITCHEN AID MIXER!! To replace it would have been hundreds of dollars.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from LEXINGTON, SC
- Parts Used:
- W11312468
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Splash from K45 KitchenAid Mixer Bowl
The shield works sufficiently. Note that the shield is not a continuous circle as shown in the picture. This actually can be an asset because it can be installed or disassembled without stopping the mixer of having to lift the head while running.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from MARION, IN
- Parts Used:
- WPW10112253
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
The mixer would not spin so I assumed it was a bad worm gear
I watched a video on how to replace the worm gear. When I opened the mixer I noticed a small screw laying in the grease. I removed as much grease as I could and could not find anywhere that the screw would have come from. All the gears turned and looked fine so I replaced the grease put the mixer back together and it worked fine. I am thinking the small screw must have somehow fallen into the mixer when manufactured. So proud of my 70 year old self for getting the job done.
Was this instruction helpful to you?
Thank you for voting!
Replaced a feb 1976 2 prong cord
Got a harvest gold mixer from g maw and thought a project would be nice we have several of these mixers in the family i knew a 2 prong cord was not safe so i took apart the mixer and wanted to regrease it just give a lookie to see what i needed and then i decided after watching video on y tube to convert to a solid state.
Parts select as a whole has been very understanding as a whole and i will continue to get parts thru them they are genuine parts which is something i had to have i have 90% of my parts for a full overhaul we just cannot get the parts delivered fedex and usps i specify the address and they deliver 2 blocks east of the house thanks for honest neighbors usps was late as usual like i said parts select is outstanding at placing the order and appliances can be fixed super simple with the right tools the concern is with the fedex and usps now they are shorthanded but lets be real but when you deliver a package just triple check it is the right house !
Parts select as a whole has been very understanding as a whole and i will continue to get parts thru them they are genuine parts which is something i had to have i have 90% of my parts for a full overhaul we just cannot get the parts delivered fedex and usps i specify the address and they deliver 2 blocks east of the house thanks for honest neighbors usps was late as usual like i said parts select is outstanding at placing the order and appliances can be fixed super simple with the right tools the concern is with the fedex and usps now they are shorthanded but lets be real but when you deliver a package just triple check it is the right house !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray from Roanoke, VA
- Parts Used:
- WP240210-2
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
pinion teeth sheared off the shaft
Repair went well after I figured out how to dis-assemble the mixer. Used straight & phillips screwdrivers and a small hammer & punch to drive out 3 pins. Ordered part# PS734233 pinion & shaft as shown in the parts page, it arrived on schedule, received part # 240210-2. Only problem was the new pinion had 10 teeth, the old/failed pinion had 11 teeth. Could not learn from anyone I called at PartsSelect or Whirlpool if the 10 tooth pinion was the correct part to use.
The teeth appeared to mesh with the mating gear,
installed the new pinion, reassembled and it worked fine. Not sure if it made a noticable difference in the output shaft speed.
The teeth appeared to mesh with the mating gear,
installed the new pinion, reassembled and it worked fine. Not sure if it made a noticable difference in the output shaft speed.
Was this instruction helpful to you?
Thank you for voting!