4KB25G1XMC5 KitchenAid Mixer - Instructions

Taking apart the machine is really easy. I was worried the grease would have spilled all over the places, but when the machine is cool, the grease is solid, so no spill. Replace the parts is quite straightforward, and there are plenty of tutorials on line. The only tip is that the grease used by KitchenAid is dark, and it is not easy to see all the small parts when you take the gearbox apart, so pay attention at what you do and at what you throw away... when I got to put it back together I missed a special concave washer which must have been trapped in the grease. Other than that... it has been an easy repair, the mixer is back up and running and I saved a ton on $$$

I have replaced so much on this mixer I can take it apart in my sleep. # speed controllers and now 2 gears. just wish we still had the 40 year old mixer we had, never half as many problems. New are not made like the old.

Unscrew the top and remove it , 4 more screws to remove the top of gear box , wipe out the old grease , lift the gears , but to remove the center gear you need a special narrow tip plier to remove the snap ring . Changed the center gear , apply new food grade grease and with reverse order putting back all remaining parts . Worked fine .

Took off all the screws to open the mixer and install the new parts.

REPLACE SPPED CONTROL SWITCH

When I ordered a replacement assembly, I was sent a "new" replacement. As I had read up on your site to number the 5 wires BEFORE I removed them, this was a great idea. The new assembly was wired differently than the original board. Although no install instructions came with the new part, it was just a matter of connecting the NUMBERED wires to the new configuration. The first time I fired it up after plugging everything in, nothing happened! I removed all the plug-in wires and reinstalled to ensure I had not gotten a tight connection because of the plastic covers over the end connectors. On my second try, everything worked as advertised! VIOLA!!!! It was a bit tough because of the tight spaces within the motor housing and the new wire routing. Just take pictures of the area BEFORE you disconnect anything and you should do o.k., since I did. 20 minutes.

Found a kitchen aid repair video. Found your site for the part I needed. The connections were not like what the video showed but there were enough connector symbols that I was able to understand where they needed to connect. Marking the connections helped for making the new connections when the new circuit board came.

At first thought part was incorrect as the electrical connection tabs on the circuit board were not inline as the existing part. However, upon closer examination I realized that the same quantity of tabs existed on the new part and although not inline, were clearly marked the same as the original part. Unit was easily replaced and is operating just like new.

Could not get it properly installed. Had to take to a repair center for completion.

my hasband did the work and i an so happy it is working good for me now,

Called original Kitchen Aid and advised had been sold and to look for Kitched Aid on web. Found site, went to appliance diagram and obtained part number and ordered. When parts came in just unscrewed and replaced new feet.

inspected and replaced worn components

I removed the decorative band that covers the seam by removing 1 screw. I then removed the top portion of mixer by removing 4 square head screws. You will then see the gear housing in the front of the mixer. Remove the 4 screws holding that on. There are no spring that are going to pop out and you never know where they went, but be careful because there is a lot of grease and a gear that it just laying in there on the right side. You will see the stainless shaft with a couple on gear cogs on it. Remove the retaing spring from the shaft and pull the top gear off, it may be a little snug. You will then see the dowel pin, mine was sheared off but I could see where it was. Be sure to remove the broken pieces. Use the punch to knock out the remaining pin. Replace with new pin making sure it is evenly exposed on both side of the shaft. Replace the top gear, then the retaining spring, the the gear housing cover, then the mixer top cover and finally the decorative band. Be sure to unplug before you start. These mixers are expensive and expensive to have someone fix them. I ordered 2 pins because shipping is a little high and the pin is cheap. I fixed this for $17.00 total and have a spare pin.

Dear Customer Service,

I just would like to express my gratitude for your wonderful service. I received my part for my Kitchen aide mixer on time as promised. The part fit perfectly. Thanks you PartSelect for being there.
What a Great Site!

A Happy Customer!

took it apart. more grease all over. Put in all but one gear on the top. The noise is still there going to try to but the old bearings in and try again. I went back to the old worm gear and allmost all the noise stopped. I did put the new bearings in and the other gears. It seems that the gear on the worm gear was cut wrong. The noise was tear able. I tried the different parts I ordered one at a time. To find out which one stopped the noise. Every time I took a part I had grease all over. It took so long every time I put in a new part to put the trans back together again. I had grease all over.