4KB25G1XMC5 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joseph from Mentone, CA
- Parts Used:
- W11086780
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
none
followed directions given, removed all the old grease .did a short test run , then replaced with new grease. the reason the gear was striped was my fault mixing too much bread at one time. we have a coffee house and use the mixer every day.
Was this instruction helpful to you?
Thank you for voting!
mixer was very noisy when running and made a horrible grinding sound
My husband removed screws and took top off mixer. Then he took out the gears and cleaned them from all the grease. After he did that he could see the gears that were all worn. We went on line ordered the new gears and in a couple of days the parts were here and he put them back in and greased it all again and put the top and screws back in place. Mixer sounds much quieter. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from North Olmsted, OH
- Parts Used:
- WP9706885
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Part broken
Easy thanks to your instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stuart from Pittsford, NY
- Parts Used:
- W11086780
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Gear Stripped was trying to replace
Could not get it properly installed. Had to take to a repair center for completion.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jamie from Jamestown, ND
- Parts Used:
- W11086780
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
gear teeth worn off worm gear
replace worm gear
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reza from STAMFORD, CT
- Parts Used:
- W11192795
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The mixer started making a loud knocking noise
Unscrew the top and remove it , 4 more screws to remove the top of gear box , wipe out the old grease , lift the gears , but to remove the center gear you need a special narrow tip plier to remove the snap ring . Changed the center gear , apply new food grade grease and with reverse order putting back all remaining parts . Worked fine .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from LARGO, FL
- Parts Used:
- WP9706885
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
white plastic part on the lifter handle
Took off all the screws to open the mixer and install the new parts.
Was this instruction helpful to you?
Thank you for voting!
Worm gear stripped.
Remove covers, open gear box, remove lock ring and gears to deterime which gears were bad. Remove old grease, install new gears and pack with new grease.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Madeleine from NEW YORK, NY
- Parts Used:
- WP9706648
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Speed control panel was replaced
Just followed the video.amazing!!got my kitchen aid back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- walter from SOUTH ELGIN, IL
- Parts Used:
- W11192795
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken gears
Fast
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from KIRBYVILLE, TX
- Parts Used:
- WP9706648
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Motor knob
Watched utube
video how to repair and ordered part, easy
video how to repair and ordered part, easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Coeur d'alene, ID
- Parts Used:
- WP9706648
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
motor would surge after a few moments of running then die.
so easy to remove the switch. I first marked the wires, 1-2-3-4 and then removed them from the old switch. removed the old switch and replaced with the new one and plugged in the wires as per markings. tried it out before replacing the top and it works perfectly. no longer timid about effecting repairs on my own. the diagrams on the website were a great help. this is a great company to do business with. part was here in 3 days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from STRAWBERRY PT, IA
- Parts Used:
- WP9706648
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Speed control switch went out
Unplugged wires from old switch, plugged them into the new switch. The new Switch have the mounting brackets in different places from the old one. Be sure to match up the numbers by the posts with the correct wires
Was this instruction helpful to you?
Thank you for voting!
Gear housing cracked, gear had nic in it
Removed old housing, pulled spring clip, slide on new gear and replaced clip. Put on new gasket and housing. Replaced outer cover. Done.
Was this instruction helpful to you?
Thank you for voting!
Bad control switch, striped worm follower gear.
Removed 2 screws holding the switch unplugged the one at a time.
opened the gear box cover 4 Philip screws, cleaned out the grease
removed the pinion gear, removed pin, removed the planet gear assembly replaced gears in reversed order greased it up put gear cover back on and tested worked great.
opened the gear box cover 4 Philip screws, cleaned out the grease
removed the pinion gear, removed pin, removed the planet gear assembly replaced gears in reversed order greased it up put gear cover back on and tested worked great.
Was this instruction helpful to you?
Thank you for voting!