4KP26M1XES5 KitchenAid Mixer - Instructions

Removed the lid of the mixer. Cleaned all grease and removed the worm gear. Installed new gear and packed with new grease Installed lid and checked worked perfect. Easy repair.

remove the old screw and screwed the new part in place. I like your link because it shows a picture of the fixture and you can find the part you need real easy. Will order from you again when I need it.

Removed mixer motor housing by removing 5 obvious screws.
Removed plastic transmission cover by removing 4 obvious screws.
Down load parts exploded drawing from PartSelect.com
Found the worn part by the shiny teeth on the large gear.
Found the large worm gear on the drawing and ordered the gear, and associated bearings. Did not need the seal.
Removed worn part, assembled new gear and beargings in same manner as the worn part, and placed new part in mixer.
Replaced transmission cover gasket.
Repacked grease from transmission cover onto the new gear.
Replaced transmission cover (4 screws).
Replaced mixer motor housing (4 screws).
Replaced mixer trim band around the motor houseing joing. (1 screw).
Plugged it and and it works, good as new.

I took all the grease out of the top of the mixer. Saw that the gear was worn. When the new parts came I put as much grease in as was in before. Put it back together and it worked like a champ.

The parts I received from PartSelect were higher quality than the original parts. The bevel gear and housing were originally plastic. The new ones are solid metal. The machine sounds and runs better than it ever did. The drawings from the website made this really easy. This will be my first choise for parts from now on.

I removed the motor assembly from the mixer. This left the stand assembly. The raising lift arm had to be removed by unscrewing the set screw, and then the lift arm was removed. I replaced the plastic arm bowl lift by sliding it over the lift arm, and then I had to remove the spring with a clip washer with the pliers, and replaced the spring back on to the new part. Total time about ten minutes for the actual fix, and about 45 minutes remove and reinstall the 12 screws that held the motor in place. It was well worth my efforts. The mixer arm works perfectly now.

the hardest part is removing the retaining ring (didn't buy pliers)after that it is very easy, remove ring, top gear, center pin, bottom gear,worm gear(was removed first)the grease is pretty nasty,clean off the old grease and put it all back the way it came apart,with new grease.And then PRAY !!!!!!! THANK YOU PARTS SELECT for your wonder smart staff.

per e.g. and put cover on and secured screws. Pluged in unit turned it on and it worked for 25 secs then went full speed and shut down.. repeat this several times got same results. Put old unit back in and it worked for 2 days then same results. I now suspect coil on shaft is defective. I'll order that and see. Unless some one knows of another problem.

Took off cover, marked leads, unscrewed two screws and replaced circuit board (speed swith unit). This one was really easy.

I removed the old screw with a hand tool to avoid injuring my hand. I then used my hand to install the new screw. Piece of cake. Ordering from Part Select was was a breeze. The only minor issue was the part cost $4.33 and shipping was $7.25.

The old planetary unit dropped out when it broke leaving the upper part of the broken shaft and beveled gear in the motor housing. Removed label band and upper motor housing with phillips screwdriver. Removed beveled gear housing with phillips screwdriver and pulled out broken shaft. Used snap ring pliers to remove gear retaining ring and slid gear off broken shaft and pressed out retaining pin below gear. Put seal and o-ring on new shaft and inserted new planetary unit up into bearings and reinstalled pin and snap ring. Greased top end of shaft and reassembled gear housing and motor housing. The unit works better than before as the upper part of old shaft had never been greased. The new drive shaft is much stronger than the original which had a deep groove cut around it which weakened the shaft where it broke in two.

Unscrewed stainless steel Kitchenaid band, removed screws holding down the main housing to get to the speed control panel. Removed two screws from to release the speed control panel, replaced the panel with new part, and replaced all the screws to the main housing, and stainless steel band and it worked like new. So easy, and it only took about 15 minutes to repair.

sat on the kitchen table and with a screwdriver started to disasemble the mixer,hardest part was taking snap ring off (easy after you buy snap ring pliers)as gears were lifted off noticeable wearing was present on all parts. the bearing housing on the gearcase was broken lose, the only major expense. the other parts are not expensive so i decided to renew all parts. glad i did felt proud of myself when job was done. would do it again Joe

1) Unplug power cord from outlet.
2) Remove #2 Phillips screw from metal band at the back of the mixer.
3) Remove band and set aside.
4) Remove 4 #2 Phillips screws that connect top of mixer housing with bottom.
5) Gently pry up on top housing to remove.
6) Remove two screws hold original speed board in place.
7) Old board and new board may have board components in different locations.
8) Lugs are marked Motor 1, Motor 2, Line 1 and Line 2.
9) One at a time move a lead from old board to new, making certain you match the leads up to the printing on the board. e.g.; Motor 1 must go to Motor 1.
10) When all leads are moved install new board with the two screws.
11) Put top back on and install four screws.
12) Clean and install stainless steel band.
13) Plug in and bump start to check for proper operation.

At the back of mixer is 1 screw that holds metal band. Remove to reveal 4 screws that hold top half of mixer. Inside locate transmission housing remove 4 more screws. Inside housing carefully scrape away grease and broken bits of gear. Take out worm gear drive shaft wipe off and inspect. Clean up grease inside tranny locate keeper ring on vertical shaft spread and slide off use 2 screwdrivers to jimmy gears up. Replace with new parts put back together and use fresh grease. Not too hard at all and alot cheaper than a new kitchen-aid.