5KPM5AWH0 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Karen from MARION, IN
- Parts Used:
- WPW10112253
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
The mixer would not spin so I assumed it was a bad worm gear
I watched a video on how to replace the worm gear. When I opened the mixer I noticed a small screw laying in the grease. I removed as much grease as I could and could not find anywhere that the screw would have come from. All the gears turned and looked fine so I replaced the grease put the mixer back together and it worked fine. I am thinking the small screw must have somehow fallen into the mixer when manufactured. So proud of my 70 year old self for getting the job done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Kathleen, GA
- Parts Used:
- WPW10380496, W11805888, WP240309-2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Worms Gear broken teeth from the gear.
Followed web site's videos. One step left out of video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angel from JACKSONVILLE, FL
- Parts Used:
- WPW10380496
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Won't Run
Found control backplate out of adjustment. Should be nominal 3/8".Broken speed control spring which attaches to backplate bottom.
I recommend Loctite Blue to complement locknut's when adjusting RPM of "Stir" speed
I recommend Loctite Blue to complement locknut's when adjusting RPM of "Stir" speed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jamie from FLORENCE, CO
- Parts Used:
- WP3184212
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Mixer making a grinding noise
replaced gear, and brushes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alicia from INDIANAPOLIS, IN
- Parts Used:
- 3179280
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Base needed replaced
I didn't because I am still waiting for the part to be sent to me after saying 3 different ship dates, today your company said they did not know when I would be receiving the base. PLEASE SEND THE PART!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from ELY, MN
- Parts Used:
- WPW10112253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
No rotation on mixer
You tube has great instructions! I would suggest when you buy a part to let customer know that they need a food grade gear grease ordered to complete the reinstall of all gears and body parts!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from CEDAR CITY, UT
- Parts Used:
- WPW10112253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Plastic worm gear gave way (as designed) when the grain mill over-worked it.
I did exactly what the PartSelect video demonstrated after watching other DIY videos on the Internet, thus I did not remove the stand which seemed like a little too much for a simple straight forward repair. This is the second time I have replaced this gear. The first time was about 10 years ago when the bakelite gear broke on a 30 year old KitchenAid K
-45. That mixer made hundreds of loaves of bread after grinding many pounds of wheat berries. The only reason we had to replace it was that it walked off the flour dusted counter and landed on its head when my wife had her back turned. Otherwise we would still be using it. :-)
Thanks for the excellent service and instructions.
-45. That mixer made hundreds of loaves of bread after grinding many pounds of wheat berries. The only reason we had to replace it was that it walked off the flour dusted counter and landed on its head when my wife had her back turned. Otherwise we would still be using it. :-)
Thanks for the excellent service and instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from Athens, GA
- Parts Used:
- WP240309-2
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Mixer suddenly ceased operation after sharp noise
To access the interior of the mixer, I first removed the single screw holding the cup-shaped part at the rear. Then I removed the 4 large screws on the under surface of the mixer head. Next I removed the bright metal ring around the planetary gear area by prying it off. I then pried the dish-shaped part off the shaft using a large-bladed screwdriver. This exposed 5 screws on the circumference of the planetary gear. By removing them, one can pull up the gears and see into the area below. I found the worm gear had fractured. By removing 3 screws at the base I extracted it for closer inspection, checking for any loose pieces. Beware of the jelly-like grease. The replacement part goes into position, and one then follows the steps in reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Ingram, TX
- Parts Used:
- WP3182857
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Spring Latch broken
Take off the old one, put on the new one--start kneadin' bread. Finding a screw driver was the hard part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from SAINT PAUL, MN
- Parts Used:
- WPW10119326
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The mixer was given to my wife. Sometimes it would work or not.
When I took the back cover off I found two parts that "could" be the problem. The speed control plate was cracked which explained the spotty working. I ordered both parts and installed them very easily. The parts fit perfectly and resulted in the mixer working perfectly. I can't say enough about the excellent parts. They were perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from COLUMBUS, OH
- Parts Used:
- WPW10380496
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
I noticed that the Initials on the package indicated that the part was made in CI. That was the problem.
I decided to update the motor brushes in our KitchenA id mixer even though it operated perfectly for years. After installing the motor brushes, you sent,I plugged the cord attached to the mixer into the outlet. I selected 1 on the speed selector and nothing occurred. The mixer would not operate. I then checked the outlet to insure there was voltage present; there was voltage present. I again plugged the cord of the mixer into the outlet, selected 1, then 5, and finally 10, with no results. The mixer would not operate. Finally, I removed the motor brushes I had received from you and installed the old brushes that were originally in the mixer, plugged it in the outlet, selected 1 and the mixer operated perfectly as it did BEFORE installing the brushes you sent.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KATHERINE from INVERNESS, FL
- Parts Used:
- WPW10380496
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
over heating
followed the emailed instructions from your company
worked perfectly
thanks
worked perfectly
thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benita from West Yarmouth, MA
- Parts Used:
- WP241764
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The plastic piece inside the mixer that raises and lowers the arm
Took the mixer apart so that the broken pieces of plastic would fall out. I needed a large philips srew driver -wasn't able to improvise. A friend (male) came over so between the 2 of us we took the machine apart and put it back together. The motor works fine, It was just the arm lever and everything is working perfectly now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vernon from Orange Park, FL
- Parts Used:
- WP9708649
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Mixer Feet startarted to disintergrate and leave marks on counter
Called original Kitchen Aid and advised had been sold and to look for Kitched Aid on web. Found site, went to appliance diagram and obtained part number and ordered. When parts came in just unscrewed and replaced new feet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Auburn, ME
- Parts Used:
- WPW10112253
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
worn gear
dissassembled mixer and replaced gear
Was this instruction helpful to you?
Thank you for voting!