KSM90PSAC0 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Rosa from GLOUCESTER, MA
- Parts Used:
- WPW10112253
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Wasn’t spin any moore
Follow a YouTube video step by step
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from SUQUAMISH, WA
- Parts Used:
- WPW10112253, WP9705444
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Replaced worn out gear
Fairly easy if you have done it once before.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from SPOKANE, WA
- Parts Used:
- WP3180526, WP240775-1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
noisy
disassembled replaced part reassembled now works well
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marc from MOBRIDGE, SD
- Parts Used:
- WPW10325124
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
mixer wouldnt turn on
watched an internet video to see what to do. Unfortunately even after replacing the chip the mixer it still didn't work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mrs Brenda from LYNNWOOD, WA
- Parts Used:
- WP9709194
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Screw cracked on the front of the mixer
Skewer the screw in with my fingers,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from RICHMOND HILL, GA
- Parts Used:
- WPW10380496, WP3184212, WP116287, WP116286
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
None
I removed the spring loaded brush screw on the side of my mixer and lost it the next day. I found a schematic of this part on your website and ordered the four pieces that make up the brush screw(?). They arrived in just a few days and I referred back to the schematic to put it together. I then popped it in my mixer, screwed it down, plugged her in and away we go! Easiest repair I’ve ever done! I’m a 70 year old retired lady and not very handy, but this was an easy fix! Thank you, PartSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenda from SANTA FE, NM
- Parts Used:
- WP243368
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken beater shaft
Used the diagram on the website and a video
Totally worked!
Totally worked!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from JACKSON, TN
- Parts Used:
- WP9704329
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old wire whip was broken
Just put on the new whip...exactly like old one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from FAIRFIELD, CT
- Parts Used:
- WPW10191926
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old screw cap wore out and would not hold bowl when mixing heavy batters.
Unscrewed old Screw Cap, tapped it out with hammer. Replaced with new screw cap that was slightly different and tight. Tapped it in with piece of wood over it and hammered it on. No problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LEONA from PORT ST LUCIE, FL
- Parts Used:
- W11396625
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Cord split in half
I removed one screw on back, once inside mixer I removed the ground screw then pulled off the black and white push on caps, then I reversed everything to get it installed, very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gordon from West Stockbridge, MA
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Base plate destored
I removed three screws, pulled off the old base plate.
Put new base plate in place and replaced the screws
Put new base plate in place and replaced the screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from AURORA, CO
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bowel would come out of screwcap when making dough for pasta
The repair was easy only requiring a phillips head screw driver to remove the old screw cap. The new screw cap fit snuggly and required a little downward pressure from my hand to seat it. Then I simply tightened the screws. Good as new for this 30+ year old mixer. My wife loves this mixer that was given to her by her Aunt. Glad we could keep it going.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from Mount Clemens, MI
- Parts Used:
- WP9704329
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Very Happy
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from FLINT, MI
- Parts Used:
- W11200218
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Bad gears
Easily took apart and replaced gears. thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Custer, SD
- Parts Used:
- WP240309-2
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
mixer making thumping noise
disasembled found stripped gesr assembly ordered and replaced went very smoothly. It would have been good to have info and acsess to the correct gear grease to use in a mixer / food grade but it worked out well anyway.shipping was very fast thanks
Was this instruction helpful to you?
Thank you for voting!