KSM103 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jennife from Lancaster, PA
- Parts Used:
- WPW10112253
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Worm gear broken
I called my fiancée.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Burnsville, MN
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
When using the bread hook, the force of the dough would knock the bowl out of the retaining ring on the mixer (Cap-Screw.)
Three phillips-head screws held the "Cap Screw" in place on the stand of the mixer. After cleaning the stuff out of the screw slots, the screws came out surprisingly easy. After the plate was lifted off, we cleaned the residue from under the plate, placed the new one in position and easily screwed in the 3 screws.
We were very pleased by the quick delivery of the part.
We were very pleased by the quick delivery of the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from MERRY HILL, NC
- Parts Used:
- W11174552, W11170663, WPW10325124, WPW10119326
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
BOARD-PHAS POINTS WORN AWAY AND 1 BRUSH STUCK AGAINST COIL
Took out stuck brush assy cleaned it and the coil and reinstalled it.
Googled internet to see how to best remove and replace Board-Phase as no instructions came with parts. Actual work replacing parts took only a few minutes. The main work was tearing down the working head to get to the parts and putting it back together. Also had to google how to adjust speed control plate to the correct speed. It helps to have patience and instructions.
Googled internet to see how to best remove and replace Board-Phase as no instructions came with parts. Actual work replacing parts took only a few minutes. The main work was tearing down the working head to get to the parts and putting it back together. Also had to google how to adjust speed control plate to the correct speed. It helps to have patience and instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darlene from North Liberty, IN
- Parts Used:
- WPW10672617
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Kitchenaid has bad white coated beaters that peal off
None
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from FREEPORT, TX
- Parts Used:
- WPW10330804, WPW10325124, WPW10119326
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
use your phones to take pic of how the wiring is to be reconnected, take pleanty from all angles
repair is farly simple just take your time, First attempted i didnt replace the speed covernor looked ok but had problems getting slow end to work properly decided to go ahead and install since i purchased it also and walia took care of the cogging problem. Good Luck
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alice from St Louis, MO
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plastic boke on the old thumb screw
unscrewed the old one........screwed in the new one, no chance for electrocution or power tools..........darn!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Wewahitchka, FL
- Parts Used:
- WPW10112253, WP9705444
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
mixer would not turn
removed the screws holding the mixer housing and then removed the worn worm gear by removing the roll pin holding it on the shaft. Replaced the worm gear and inserted the pin that hole it in place. Replaced some of the gear grease and reassembled mixer. Went very easily. No problems at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from MARTINEZ, CA
- Parts Used:
- WPW10330804, WPW10325124, WPW10119326
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Mixer would not turn on
Pulled off end cover. Used the how-to video's to show me how to remove the (3) components (watch out when it comes to removing the spring). Removed all (3) components (one issue was the black cardboard seal, which because of its age broke. Hindsight tells me that I should have purchased a replacement seal along with the (3) new parts.
Fixed the broken part of the seal with scotch tape). Installed all new parts with the help of the video's and put the cover back on. Even with the new parts, the mixer would not run. Come to find out, after I took it to an appliance repair person, that someone had pulled both brushes and put them back in improperly. I could not find a how-to video that showed me how to de-install/re-install the brushes properly. I assume that was because new brushes were no longer available for purchase. At any rate, when the brushes were put in properly, everything worked. The repair person also adjusted the (2) screws on the speed control plate so that when you change the speeds via the lever, it all works properly. I didn't find a how-to video covering those adjustments either.
Fixed the broken part of the seal with scotch tape). Installed all new parts with the help of the video's and put the cover back on. Even with the new parts, the mixer would not run. Come to find out, after I took it to an appliance repair person, that someone had pulled both brushes and put them back in improperly. I could not find a how-to video that showed me how to de-install/re-install the brushes properly. I assume that was because new brushes were no longer available for purchase. At any rate, when the brushes were put in properly, everything worked. The repair person also adjusted the (2) screws on the speed control plate so that when you change the speeds via the lever, it all works properly. I didn't find a how-to video covering those adjustments either.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EUGENIO from MIAMI, FL
- Parts Used:
- W11192794
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
spent Pevel Pinion Center Gear
remove the back cover part # 36, remove the top cover part # 1 (by removing the chrome ring parate # 28, the mobile disk part # 25 and six screws part # 24). This done, remove the system parat # 38 to release the Pevel Pinion Center Gear part # 15 and remove the damaged part and put the new part. The install the removed parts in reverse order as they withdrew.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from COLUMBIA, NJ
- Parts Used:
- WP9705444
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Pin was missing therefore no mixing function
Place Pin in hole where it was missing then gently tap pin into place
Run a test and all is good ??
make sure to use a drift pin set
Tom
Run a test and all is good ??
make sure to use a drift pin set
Tom
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peggy from Escondido, CA
- Parts Used:
- WP9709194
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
plastic outer casing on tightening screw had broken
This is the tightening screw that holds the attachments into the motor unit of the mixer. Found your web site and reordered 2 replacement pieces (in case one breaks!). Very EZ and user friendly. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stanislaw from San Antonio, TX
- Parts Used:
- WP9704329
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken wire whip
no instructions necessary
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry S. from OLIVE BRANCH, MS
- Parts Used:
- W11174552, WPW10330804, WPW10325124, WPW10119326
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Only worked on high speed
Followed the video on your website and it was super simple!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kate from BELLINGHAM, WA
- Parts Used:
- WP4162324, WP240309-2
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The smallest gear was broken, so we got the worm gear and bracket as well as a new gasket and some lube to grease the gears
We disassembled it with the help of a YouTube video from partselect.
We saw the damaged gear, removed the 4 screws to remove it, cleaned all the old grease out with rags so it wouldn't be contaminated by metal shavings.
We reassembled it per the YouTube video and it works better than ever!!
Make sure you remove the roll pin before trying to pry off the planetary plate, because I watched a different video first, which didnt tell me that and i bent it a bit.
We saw the damaged gear, removed the 4 screws to remove it, cleaned all the old grease out with rags so it wouldn't be contaminated by metal shavings.
We reassembled it per the YouTube video and it works better than ever!!
Make sure you remove the roll pin before trying to pry off the planetary plate, because I watched a different video first, which didnt tell me that and i bent it a bit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from DEXTER, NY
- Parts Used:
- WPW10323373, WPW10112253, WP4162324, WP240210-2
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Gear-worm teeth stripped, teeth on pinion shaft worn to sharp edge and case gasket dried out. Not bad for a 20 yr. old mixer.
Looked at the mixer schematic form your website,which made it easy for me to take it apart. Once it was apart & all the grease removed I disassembled & cleaned all the drive parts. Saw what was warn, ordered the parts from you. Three days later received the parts, everything fit perfect. Added grease,assembled the mixer and it ran perfect, good for another 20 yrs. Thank you for making it so easy to repair an old mixer in just over two hours. Rolf
Was this instruction helpful to you?
Thank you for voting!