4K5SSWH1 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- GLADYS from HAYWARD, CA
- Parts Used:
- WP3182857
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
spring latch broke
removed old screws and latch, replaced it with the new. took just a few seconds. This is the first time i ever fixed anything. customer service was amazing
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claudia from felton, CA
- Parts Used:
- WP241764
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The mixer bowl would not go down.
First of all I found the part in no time flat and ordered it early afternoon and it was at my door within 24 hours! My son was off work one day and I asked him if he needed a job to do and he said "sure". So I showed him the new part and where it goes and in less then 10 min it was working. awesome!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bernadette from Hackensack, MN
- Parts Used:
- WP3182857
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bowl spring broke in two pieces
Removed the two screws that hold the bowl spring in place. Removed broken spring. Replaced broken spring with replacement spring. Tightened two screws that hold it in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from SAINT LOUIS, MO
- Parts Used:
- WP9708649
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
needed to replace rubber foot on mixer
The insertion part of the foot was tapered to fit in the hole in the mixer. Simple pressure was not the answer. So I used a small key, placed it on the bottom of the foot, after applying a little vegetable oil on the foot, and tapped it into place. Worked well.Joe
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- per from highland, MI
- Parts Used:
- WPW10112253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
no mixing
dis-assemble, replace part, re-lube, reassemble, test good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Custer, SD
- Parts Used:
- WP240309-2
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
mixer making thumping noise
disasembled found stripped gesr assembly ordered and replaced went very smoothly. It would have been good to have info and acsess to the correct gear grease to use in a mixer / food grade but it worked out well anyway.shipping was very fast thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from CIRCLE, MT
- Parts Used:
- WPW10323378, WP67500-55, WP4162324
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
oil leak
just as the you tube instructions said.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rejana from FAIRVIEW PARK, OH
- Parts Used:
- WP240309-2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The worm gears were broken.
We simply replaced the gear with the new one. It was very easy to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from FLINT, MI
- Parts Used:
- W11200218
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Bad gears
Easily took apart and replaced gears. thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Naperville, IL
- Parts Used:
- WP240309-2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
stripped nylon drive gear
Followed the repair instructions from the manual. ...
I did notice that the replacement part had an extension on it that allowed for the gear grease to be "pulled up" onto the drive gear ( the one that broke), while the unit is running. This feature was not on the original part, but was obviously an upgrade design which was added after my particular mixer was made. I think that the extension on the bracket will help prevent the new nylon gear from binding and stripping as we use the mixer from now on.
I'm glad that PartSelect had the more modern part on hand, and not just an "overstock" from the original, inferior design.
I did notice that the replacement part had an extension on it that allowed for the gear grease to be "pulled up" onto the drive gear ( the one that broke), while the unit is running. This feature was not on the original part, but was obviously an upgrade design which was added after my particular mixer was made. I think that the extension on the bracket will help prevent the new nylon gear from binding and stripping as we use the mixer from now on.
I'm glad that PartSelect had the more modern part on hand, and not just an "overstock" from the original, inferior design.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GARY from BECKLEY, WV
- Parts Used:
- WP240309-2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
turn and quit
Disassembled gear housing and replaced worm gear/bracket assembly. The hardest part was cleaning and working around what looked like 2 pound of grease. I will contact you again if I need parts for anything. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- anthony from harviell, MO
- Parts Used:
- WP240309-2
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
plastic worm gear was stripped would nut turn
replaced worm gear and wonderd why they used plastic instead of a stronger metal gear, unit works fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BRIAN from PALISADE, CO
- Parts Used:
- WPW10112253, W11192794, WP4162324
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Decorative plug at top of mixer fell into the bowl and jammed the mixer stripping gears
Watch U Tube video. Take care to keep track of disassembly. Hard part was to have 4 types of screw drivers to fit the different screw heads. Be sure to clean broken gear clogs out of the grease. Parts select lady was a great help. Download Parts select diagram for extra help. Time and patience!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rachael from SEATTLE, WA
- Parts Used:
- WPW10112253
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
Worm gear was stripped and needed to be replaced
I am not handy, but was able to follow this YouTube video and do this repair easily and successfully: https://www.youtube.com/watch?v=1QsgPIL9FpA
I did take the mixer apart first to verify that the worm gear was the issue, then ordered the part from you site. I received it quickly and was able to do the repair and get back to mixing in a few days!
I did take the mixer apart first to verify that the worm gear was the issue, then ordered the part from you site. I received it quickly and was able to do the repair and get back to mixing in a few days!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marvin from Hemet, CA
- Parts Used:
- WP67500-55, WP4162324
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
grease from housing leaking into bowl
Followed instructions found onllne at Kitchenaid.com and replaced seals with parts obtained from PartSelect.
Was this instruction helpful to you?
Thank you for voting!