KSM195PSPL5 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Peter from SALADO, TX
- Parts Used:
- WPW10323373, WPW10112253
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Worm gear was worn out .
I watched the university of YouTube videos, and followed their instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curt from SHELBY, MI
- Parts Used:
- WPW10112253
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Teeth on the gear were worn off.
Took each area apart. Replaced the gear and reassembled it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amelia from AURORA, CO
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Mixing bowl was no longer locking in place
Unscrewed the existing screw cap, put the new one in place, replaced the screws. So easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GALO from DECATUR, GA
- Parts Used:
- WPW10325124
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Mixer operarates at high speed only.
Removed old one and replaced with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Locust Grove, VA
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
cap screw was worn out and would not hold the bowl
Removed three screws and lifted out old part. replaced with new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from JACKSONVILLE, FL
- Parts Used:
- WPW10325124
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Mixer went to high speed immediately on starting
Simple fix actually. UNPLUG mixer and remove the one screw on top that holds on the back. The Phase control board sits under and behind the paper insulator and "switch" assy. Remove the 4 wires with a pair of needle nose pliers, the one screw holding it to the back of the mixer and install the new one in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from COXS CREEK, KY
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bowl lock wouldn't hold when mixing bread
Repair is very straight forward. Remove the existing plate by removing the three phillip head screws. Use a regular screwdriver or knife to pop the plate off. (I cleaned the area while I was there but probably not necessary) Position the new plate with the screw holes lined up. Press down to pop the plate into position. Install original screws and tighten. You're done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from HALEYVILLE, AL
- Parts Used:
- WPW10325124
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
One speed only and surging
I replaced the phase control board because the mixer had only
one speed and was surging. I noticed from other posts that it
is important to note the setting of the speed plate before you
remove it in order to remove the phase control board. Also be
careful removing the associated 'slip-on' terminals as it would
be easy to damage the speed plate. If I ever do this again I
will go ahead and replace the speed plate, probably the cheapest
item to replace. The operation was a success and the mixer is
back in business. Thanks.
one speed and was surging. I noticed from other posts that it
is important to note the setting of the speed plate before you
remove it in order to remove the phase control board. Also be
careful removing the associated 'slip-on' terminals as it would
be easy to damage the speed plate. If I ever do this again I
will go ahead and replace the speed plate, probably the cheapest
item to replace. The operation was a success and the mixer is
back in business. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sarah from GRAPEVINE, TX
- Parts Used:
- W11192794
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Attachment hub stopped spinning
Used youtube movies to disassemble the mixer and found that the gear was stripped. I kept the screws in labeled ziploc baggies so I wouldn't forget which screws went where. Once the part arrived, it was very simple to replace the gear. I regreased the mixer and then reassembled. The trickiest part was how greasy everything was! It was also hard to get the pin through the beater hub - I found a video that suggested using a very slim screwdriver to thread the hole before inserting the pin. This was the most involved part replacement I've done on my own, and it was very satisfying to get my mixer back in working order!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from CISCO, GA
- Parts Used:
- WP240309-2
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
worm gear worn out
I watched a short video on replacing the worm gear, although I did not know what the problem was until I watched the video. after the video ended I took the mixer apart and found the problem located a parts number an placed my order. got the part in one week put in the new part in about 20 minutes and it work like new. and the price was very reasonable
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sylvia from HILTON, NY
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The original screw cap would not hold the mixer bowl in place anymore.
The new part was too large for the replacement job, but we used the self tapping screws that came with the mixer and screwed them in from the bottom to open the holes a little more since the original screws were to short to hold the new plate. Then we replaced the screws with longer screws and that seemed to do the trick!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from OSSINEKE, MI
- Parts Used:
- WPW10325124
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Control stuck in high gear.
With the mixer being over 30 years old we believed it has going to have to be replaced. However, my husband jumped on uTube and looked at reviews for the problem. Motor was only running on high speed. Reviews said to replace the phase control board. Repair was very quick by just taking off the cover. Removing the old board and connecting the new. Mixer is working awesome once again. In such a disposable society it is great to be able to fix vs trash. Happy Baker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from CHARLESTON, SC
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The threads on the plate that holds the bowl had stripped and the bowl flew off when mixing
Removed old plate, screwed in new plate and works like new! Was so happy I wouldn’t have to replace my 30 year old mixer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- H. from Hollister, CA
- Parts Used:
- WP240309-2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Damaged the worm gear in our 300w mixer.
After stalling the mixer while mixing dough I found that the motor still functioned but the blade didn't move. I basically took the mixer into my shop along with a digital camera to record any complicated disassembly procedure I might have to deal with for reassembly and proceeded to disassemble the mixer. Once apart, I cleaned the mixer parts, removed the broken worm gear and bracket, and got online for someone that carried the replacement piece. PartSelect sent the replacement within 3 days and now it works great again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beverly from St. James, MN
- Parts Used:
- WP9704329
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wire whip came apart
Really no help from Kitchen Aid sources; but phone call to PartSelect solved the problem. Kitchen Aid repair line didn't even know the part #! Thanks to Part/Select, Christmas cookies are being made.
Was this instruction helpful to you?
Thank you for voting!