KSM195PSPL5 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Stanislaw from San Antonio, TX
- Parts Used:
- WP9704329
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken wire whip
no instructions necessary
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from COLUMBIA, NJ
- Parts Used:
- WP9705444
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Pin was missing therefore no mixing function
Place Pin in hole where it was missing then gently tap pin into place
Run a test and all is good ??
make sure to use a drift pin set
Tom
Run a test and all is good ??
make sure to use a drift pin set
Tom
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DONG from Elk Grove, CA
- Parts Used:
- WPW10112253
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The worm gear was broken
I removed the pin from the outside shaft,then removed all screw around the body of the mixer,then removed the top case out,took 3 screws out from the the gear assembly case......punched the pin out of worm gear then release the little shaft out from the case,replaced a new one....then starting go backward till completely all assembled don't forget lube grease to all gears and test run good very smooth.........it's ok
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reid from MONTICELLO, MN
- Parts Used:
- WPW10325124, WPW10119326
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Speed control not working properly
Replaced the speed control plate and phase control board and works well. Pay attention to speed control board spring and adjustment lever when reassembling.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosa from GLOUCESTER, MA
- Parts Used:
- WPW10112253
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Wasn’t spin any moore
Follow a YouTube video step by step
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marc from MOBRIDGE, SD
- Parts Used:
- WPW10325124
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
mixer wouldnt turn on
watched an internet video to see what to do. Unfortunately even after replacing the chip the mixer it still didn't work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from SUQUAMISH, WA
- Parts Used:
- WPW10112253, WP9705444
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Replaced worn out gear
Fairly easy if you have done it once before.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from JACKSON, TN
- Parts Used:
- WP9704329
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old wire whip was broken
Just put on the new whip...exactly like old one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gordon from West Stockbridge, MA
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Base plate destored
I removed three screws, pulled off the old base plate.
Put new base plate in place and replaced the screws
Put new base plate in place and replaced the screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenda from SANTA FE, NM
- Parts Used:
- WP243368
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken beater shaft
Used the diagram on the website and a video
Totally worked!
Totally worked!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from MARIENVILLE, PA
- Parts Used:
- WPW10112253, WP240309-2
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Mixer would slip gears under load, finally would not mix under any load
Rather than duplicate previous repair works, I recommend going to this user site and follow their instructions: http://www.neilcrockett.com/mixer1.htm. Once you have done this repair, taking the unit apart is easier to perform this tasks. Order replacement Grease "Benalene 930-2" in the 3.3 oz container and be sure to use the full container to lather all around all the gear components so grease will be available to units for years to come due to heat build up under load. Too, the 3.5 oz container is made for one unit repair job and is available through Amazon. This grease is available on larger quantities if needed / desired. I did order both, a Worm Gear and the Worm Gear and Bracket as I wasn't sure of my mechanical ability to make this repair until I got inside the unit but the worm gear is easily replaced once you clean out all the old grease. The worm gear is a neoprene type gear with all other gears being metal. I assume neoprene is used as sacrificial to save other gears from breaking under loads and years of use.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from AURORA, CO
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bowel would come out of screwcap when making dough for pasta
The repair was easy only requiring a phillips head screw driver to remove the old screw cap. The new screw cap fit snuggly and required a little downward pressure from my hand to seat it. Then I simply tightened the screws. Good as new for this 30+ year old mixer. My wife loves this mixer that was given to her by her Aunt. Glad we could keep it going.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from FAIRFIELD, CT
- Parts Used:
- WPW10191926
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old screw cap wore out and would not hold bowl when mixing heavy batters.
Unscrewed old Screw Cap, tapped it out with hammer. Replaced with new screw cap that was slightly different and tight. Tapped it in with piece of wood over it and hammered it on. No problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from Mount Clemens, MI
- Parts Used:
- WP9704329
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Very Happy
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GARY from BECKLEY, WV
- Parts Used:
- WP240309-2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
turn and quit
Disassembled gear housing and replaced worm gear/bracket assembly. The hardest part was cleaning and working around what looked like 2 pound of grease. I will contact you again if I need parts for anything. Thanks.
Was this instruction helpful to you?
Thank you for voting!