5KSM185PSEKG5 KitchenAid Mixer - Instructions

Three phillips-head screws held the "Cap Screw" in place on the stand of the mixer. After cleaning the stuff out of the screw slots, the screws came out surprisingly easy. After the plate was lifted off, we cleaned the residue from under the plate, placed the new one in position and easily screwed in the 3 screws.
We were very pleased by the quick delivery of the part.

Inserted new pin and tightened set screw.

Took out 3 screws, removed old plate, put down new plate the tightened screws. Runs like new, great service, price, quick delivery!

Turned the mixer on its side and slid the part into the bottom of the base.

removed the screws holding the mixer housing and then removed the worn worm gear by removing the roll pin holding it on the shaft. Replaced the worm gear and inserted the pin that hole it in place. Replaced some of the gear grease and reassembled mixer. Went very easily. No problems at all.

remove the back cover part # 36, remove the top cover part # 1 (by removing the chrome ring parate # 28, the mobile disk part # 25 and six screws part # 24). This done, remove the system parat # 38 to release the Pevel Pinion Center Gear part # 15 and remove the damaged part and put the new part. The install the removed parts in reverse order as they withdrew.

Place Pin in hole where it was missing then gently tap pin into place
Run a test and all is good ??
make sure to use a drift pin set
Tom

Punched out the roll pin to remove eccentric from spindle, undid 5 screws (after removing trim ring), and removed 4 screws to undo the motor housing. Make sure to keep the one screw with a lock washer in the BACK of the housing. Undid the screw on top to remove the back of the motor housing to take out the strain relief grommet, prior to removing the motor housing. Scraped the excess grease into a tub to re-use. Pulled out the shaft, and lifted out the old (stripped) gear and plopped the new one in. Make sure to mark match points for parts, and put the pins back in in the right order. You have to put the 5 screws back in before sliding the trim ring on, and putting the roll pin back. make sure all gears mesh and test before snugging the motor housing screws. Be sure to orient the strain relief grommet securely, and be careful of the filter plates in the back of the housing (they're brittle). putting the grease back is like frosting a cake. Save a little for the planetary ass'y.

Literally the whole top of this stand mixer had to be taken apart. With the help of U-tube! We realized the silver strip was removable and there where screws underneath. We figured we would replace both parts while it was all taken apart. We cleaned the mixer and added some grease where necessary. I now have a 25 year old new mixer. Thanks for having our parts and guiding us with a diagram of the unit. Very helpful.

I removed the pin from the outside shaft,then removed all screw around the body of the mixer,then removed the top case out,took 3 screws out from the the gear assembly case......punched the pin out of worm gear then release the little shaft out from the case,replaced a new one....then starting go backward till completely all assembled don't forget lube grease to all gears and test run good very smooth.........it's ok

Rather than duplicate previous repair works, I recommend going to this user site and follow their instructions: http://www.neilcrockett.com/mixer1.htm. Once you have done this repair, taking the unit apart is easier to perform this tasks. Order replacement Grease "Benalene 930-2" in the 3.3 oz container and be sure to use the full container to lather all around all the gear components so grease will be available to units for years to come due to heat build up under load. Too, the 3.5 oz container is made for one unit repair job and is available through Amazon. This grease is available on larger quantities if needed / desired. I did order both, a Worm Gear and the Worm Gear and Bracket as I wasn't sure of my mechanical ability to make this repair until I got inside the unit but the worm gear is easily replaced once you clean out all the old grease. The worm gear is a neoprene type gear with all other gears being metal. I assume neoprene is used as sacrificial to save other gears from breaking under loads and years of use.

I removed three screws, pulled off the old base plate.
Put new base plate in place and replaced the screws

Fairly easy if you have done it once before.

Follow a YouTube video step by step

Unscrewed old Screw Cap, tapped it out with hammer. Replaced with new screw cap that was slightly different and tight. Tapped it in with piece of wood over it and hammered it on. No problems.