4KSM150PSGR0 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Terry from Pigeon, MI
- Parts Used:
- WPW10112253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Worm gear was missing teeth
Took the mixer apart and cleaned the grease so off I could see the pins. Wasn't a hard fix only thing is make sure to clean the grease off so you can see what your doing
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- terry from eudora, AR
- Parts Used:
- WPW10672617
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
very simple could not been a easer job thank for partsSelect.
all that were required, were you take off old beater an replace new.simple push up old part an replace new. as you do after usage of the machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- A. W. from Rogers, AR
- Parts Used:
- WP240309-2
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
The Kitchenaid heavy duty mixer's motor would run but the mixer head would not turn.
Obviously the problem was in the gear box of the mixer. I disassembled the gear box by removing the four large screws holding the base then the four screws at the rear and center of the mixer. Then I removed the thin metal ring covering the five screws around the front of the housing by gently prying up with a small screwdriver. The five screws beneth the ring have to be removed with a small blade screwdriver turning them a round at a time in sequence until they are free. Gently pry the two housings apart with a screwdriver and lift our the lower half with the plantary gears. I found the drive gear was stripped. I went to PartSelect on the web, eaisly found the exploded view of the mixer's gear box and ordered the gear I needed. The gear is part of an assembly attached to the mixer housing with three screws. Work around the lubricant in the housing. Within four days I received the new gear, installed it by reversing the above procedures and the mixer is working again. The total cost was $34.85. Not a bad investment considering the mixer cost over $400 and would have been trashed for want of one part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pat from Marshfield, WI
- Parts Used:
- WPW10672617
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The coating was chipping off of the original Flat Beater
All I had to do was insert the new beater. Wonderful timing, was just going to start some holiday baking. will definetly use your website again. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- .JENNIFER from STAR, ID
- Parts Used:
- WPW10672617
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
powder coating came off mixer paddle.
put new paddle on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Edgewater Park, NJ
- Parts Used:
- W11200218, WP4162324, WP240309-2
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Broken worm gear
Removed old gear and grease and replaced gear and grease resembled
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juanita from Ferndale, CA
- Parts Used:
- WPW10672617
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed new flat beater
Just replaced the beater.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from CARLISLE, PA
- Parts Used:
- WP9709707
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing pedestal foot
Turned the mixer on its side and slid the part into the bottom of the base.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from Great Bend, KS
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replace base plate on KitchenAid mixer
Took out 3 screws, removed old plate, put down new plate the tightened screws. Runs like new, great service, price, quick delivery!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennife from Lancaster, PA
- Parts Used:
- WPW10112253
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Worm gear broken
I called my fiancée.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Burnsville, MN
- Parts Used:
- WPW10191926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
When using the bread hook, the force of the dough would knock the bowl out of the retaining ring on the mixer (Cap-Screw.)
Three phillips-head screws held the "Cap Screw" in place on the stand of the mixer. After cleaning the stuff out of the screw slots, the screws came out surprisingly easy. After the plate was lifted off, we cleaned the residue from under the plate, placed the new one in position and easily screwed in the 3 screws.
We were very pleased by the quick delivery of the part.
We were very pleased by the quick delivery of the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Columbus, OH
- Parts Used:
- WP16910
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Pin was missing on mixer allowing head to move.
Inserted new pin and tightened set screw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from GREENWOOD, IN
- Parts Used:
- WPW10112253, WP9705444
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
planetary gear would not turn; discovered worm gear was broken upon dis-assembly of mixer
Followed step-by-step video instructions for dis-assembly/reassembly found at ereplacementparts.com. All went well except when driving out the pin that holds the worm gear in the tower. The video wasn't exactly clear enough about what position the pin should be in when driving it out and I inadvertently drove the pin out so that it was trapped inside the tower assembly. Result? I had to bend the pin to get it out, causing an extra expenditure and wait time to order a new pin. So, lesson learned: be sure the pin is horizontal to the tower and not perpendicular to when driving the pin out. Also, I found that having the mixer apart was a good time to replace the grease in the housing. I don't think it would be required to replace the grease at this time but I was worried that pieces of the old worm gear could remain in the grease and possible get jammed in the gears after repairs were completed. Be sure to get a "food grade" grease not grease from your local auto parts store! The table knife was the best tool to use to remove the grease and to smear the grease all over the internal gears when replacing it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from FREEPORT, TX
- Parts Used:
- WPW10330804, WPW10325124, WPW10119326
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
use your phones to take pic of how the wiring is to be reconnected, take pleanty from all angles
repair is farly simple just take your time, First attempted i didnt replace the speed covernor looked ok but had problems getting slow end to work properly decided to go ahead and install since i purchased it also and walia took care of the cogging problem. Good Luck
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Wewahitchka, FL
- Parts Used:
- WPW10112253, WP9705444
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
mixer would not turn
removed the screws holding the mixer housing and then removed the worn worm gear by removing the roll pin holding it on the shaft. Replaced the worm gear and inserted the pin that hole it in place. Replaced some of the gear grease and reassembled mixer. Went very easily. No problems at all.
Was this instruction helpful to you?
Thank you for voting!