22305 (1988) Kenmore Miscellaneous - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
bearing went out in blower motor
removed old motor from cooktop & motor housing & replaced w/ new motor & parts to install same. parts needed where screws & isolators (3).All went ok
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adam from Kempner, TX
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
heating coils would not work
Remove heat coils, take body of coil inserts out, remove screws from body, cut old receptacle out, tie new recptacle wires to the old piece of left over wires using wire nuts, and reassemble body, insert heating coils and test.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Llewellyn P. from Junction, TX
- Parts Used:
- W11120795
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Jennaire 4 burner stove top right two burners coming on full heat with either controls.
Read privious fixes. Didn't know which control was bad but ordered two new ones. Marked locations of switch contacts and wire colors. Removed old controls. Installed new replacements and everything works fine. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gina from Oak Harbor, WA
- Parts Used:
- W11120795
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
A burner on the cook top stopped working
I switched the circuit breaker off at the electrical panel, removed the burner switch assembly (two screws) from the cook top. The burner switches are held in place by a single nut over the control stem. I unscrewed the nut from the failed switch, disconnected the four electrical leads (one by one) from the old switch and connected them in the same position on the new switch and replaced the nut. The clips on the electrical leads were oxidized/tarnished so I cleaned them with emery cloth to assure good contact with the posts on the switch. Replaced the burner switch assembly in the cook top, energized the circuit and the burner works perfectly again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darwin from wisconsin rapids, WI
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Not heating
Was easy cut the wires of as told to do wire nut the ends together and put back together and tested and worked great. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald E. from Marissa, IL
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
burners would not come on without moving them around
took old screw out of stove top that held them in and cut the two wires off close to the burner stripped the wires and used the screw caps to put each line together it doesn't matter which line goes where and screwed it back on with the old screw and tried the two burners and they both worked job done ps it took longer for me to type this but i am slow at typing
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Greybull, WY
- Parts Used:
- WPY04100166, 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Burner on stove didnt work
It was a very easy project...Removed the stove top a few screws..snipped a couple of wires and attached the new receptacle...everything needed was in the package...They even have a video on here that was very helpful..shows how easy it really is...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vittorio from Wakefield, MA
- Parts Used:
- 12001676
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Electric surface burner would only turn very hot
Well, I had to search a bit deeper in the internet to find out that the problem was not with the surface burner (which did look a bit burned out anyway) but rather with the surface burner switch (Part Number: PS336885) which must have ben damaged by the heat of the closest burner. If this problem would have been better documented (or if I would have searched more carefully) I would have saved over $40 with parts (Surface Burner Receptacle Kit) that I didn't quite need. Repairing the switch was very easy, thanks also to the available video , even though the stove used on this video (front panel) didn't quite match mine (top-back panel).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elroy from Atwater, MN
- Parts Used:
- 12001676
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
burner not operating or intermittently
Shut off power at breaker box. Removed top burner unit. Removed old receptacle (Mounting screw was rusty so I drilld out the old one.) Cut wires from old unit. Stripped wires back on old unit. Attached old and new wire with ceramic wire nut. Attached new unit. Reinserted top unit. Reconnected power and "voila". Wife was smiling again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kerry from Silverado, CA
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner receptacle had malfunctioned and been removed
10 Minutes for a stove my landlord thought was not fixable (repairman had already cut the wires to the element and capped them)! The delivery person handed me the package, I got out the single tool needed, installed the part, put away the tool, cleaned my hands, and put a pot of water on the stove to boil for pasta. 10 minutes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- martien from williamstown, MA
- Parts Used:
- 12001676
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
one pole of the socket corroded to nothing
Starting by me making a substitute prong to keep the stove working while the part this coming by mail. was a piece of cake.
Was this instruction helpful to you?
Thank you for voting!
broken surface burner knob
Pulled off the knobs,replaced switch, put on the new knobs. Your web site is easy to use, and your parts are first quality. Dave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John J from Coatesville, PA
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Porcelan Electric Burner Plug broke
The video on your website showed me how to take out 1 screw, cut the existing wires and strip the ends. The kit came with 2 porcelan wire nuts to re-connect the wires and it was done. Less than 10 minutes. It saved me $100.00 to get it repaired.I bought 2 in case I need another one in the future.They only cost $11.00 each. Awesome website.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Jenkintown, PA
- Parts Used:
- WPY04100166, 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
One electric burner was not heating.
I simply watched the video on the PartSelect site. That made the repair easy and fast. It took perhaps 5 minutes to bring the stove back to life again.
Was this instruction helpful to you?
Thank you for voting!