MH1160XSD2 Whirlpool Microwave - Instructions

I followed the manufacturer's installation instructions. Everything worked perfectly.

put the turntable in and had a Rum and Coke to celebrate. Your service was GREATTTTTT...

This is an under the counter microwave. Simply removed the two screws holidng the vent grille on top of the unit, lift out the old charcoal filter, clean the vent fan exit surfaces then replace the filter and put the vent grille back. Be careful to not drop either of the two screws after one is installed as you will have to take the grill off and start the screw installation again unless you have a magnetic to retrieve the dropped screw. An easy five minutes at most to change.

Having the correct model number helps:
Just place the parts in the microwave and it worked.

I was sent the wrong fuse by you. I had to procure a fuse in another manner. Very disappointing. The repair was simple. It just took longer because of the failure to send the correct fuse.

Open compartment, installed bulb, closed compartment

Installed new vent grillein ten minutes. New part was correct replacement part and fit perfectly.

took it to Buttermore appliance in Auburn Indiana and he changed the fan and added another fuse

Took the front off and behind a plate was the fuse, so I replaced it for what good that did!!!

1. Safely unplug the dryer. 2. Unconnect the vent hose. 3. Pull it out so you can have room to move around to work on it. I actually in a power chair so I put an old blanket on the floor and laid it face down to work on it. It was extremely dirty so I used a shop vac to clean off the back panel before starting. 4. I took off all the screws and cord cover with a nut driver, used the shop vac again to clean the entire inside. Properly a 1/2 to 1 inch of dust and lint was built up causing a dangerous fire situation for sure. Once clean, take a photos especially of where the electrical connection are. 5 Located and removed the two screws holding the element on, used a nut driver and long nose pliers to remove the heat sensor & electrical connections. 6. Dry fit the element before tightening screws to make sure placement is correct then match the holes replace the screws. 7. Using the photos put the heat sensor & electrial wires back on, you may need to use the pliers to push it on tight. Double check everything, clean back panel inside and out, match up holes replace screws, I actually checked my power cords screws for tightness then replaced cord cover. 8. Replace vent hose if needed or then reattach it and plug it up. You may need to check the dryer barrel by turning the drum around a few times. Should work perfect, you will smell the element a little but it should be ok. Remember clean your dryer inside and out every six months or so to prevent dryer fires.

I didn't do the repair -- my husband did, said it was easy, had no problems what so ever! The new bulbs give a lot more light to the cooking area.

Time to replace the charcoal filter

Removed all the screws from the underside panel - approximately 9 or 10 of them. The panel easily dropped down to allow easy access to the light bulb socket assembly. The wires to the socket easily unplugged and old socket easily removed. New socket slipped right in and wires easily plugged in. Actually took longer to put the screws back in than anything else. I am thrilled with this repair. Note: so easy even a 61 year old single woman in her PJ's can do it.

Had to take all the screws out of the bottom of the microwave to get to the socket. Once that was done, it was a simple fix of taking out 2 screws that hold the socket in, and then unplugging it. Replug and put all screws back. It was a fairly simple fix for the diy homeowner.

1. Unplug the power cord from the wall socket. 2. Remove the 10 screws holding the bottom cabinet cover in place. The bottom cabinet cover will swing down allowing acces to the inside ofe the microwave. 3. Remove the connector from the turntable motor. 4. Use a T15 Torx driver to remove the 2 Torx screws holding the motor in place. 5. Remove the motor. 6. Reverse the process using the new motor.