MH1160XSD2 Whirlpool Microwave - Instructions

Took out the turntable parts to ensure I ordered the correct cooking tray. Matching those with photos of related parts on PartSelect worked great. Put turntable drive and support ring in place and cooking tray went in very easily. Plan to order a second one to have on hand for this rental property.

Ordered the glass tray and installed it. Received the orderin about two days.

After removing the over-the-range unit (no small feat!) I had to figure out how to open the case (good puzzle!). Capacitor had already discharged, so it was very easy to reach in, pop the old fuse and install the new one! As per your advice, I found out I was a "28%-er"! Upon re-installation, the microwave "sprang to life"!! Thanks, "Part Select"!! I was already shopping around for a new machine! (Now if you could only tell me an easier way to re-mount this heavy beast over the stove!!!)

On top front of the microwave are two Philip's head screws holding the rail on. Remove these screws and the rail snap out the old filter (noting the dark side down) then snapping the new filter in. Replace rail. 10 to 15 minute task.

Ordered a new motor. Removed the outside trim of the oven-microwave combo. 2 screws at the bottom of the trim. Removed the screws that held the combination micro and oven unit in place. Removed the top and bottom black plastic grill of the microwave. 3 screws each. Pulled the entire unit out about 1 inch exposing the screws at each side of the microwave that hold it in place.
Snapped off the top control panel which exposed the wiring connecting the control panel.
Unplugged a couple of wire harness units to free the control panel.
Be sure to label the units to know which goes where during reassembly.
Remove the microwave unit from the housing and place it on its side.
Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.

Unscrewed glass panel, removed old bulb, cleaned glass panel and installed new bulb. Screwed panel back into place.

The grease filters you sent to me are not the same size as the filters I replaced!!! Since the new filters do not fit correctly the air does not get filtered since the filters are too small for the hole. Why would you send me replacements that are not the same size as the ones I replaced? The filters are in the hole of the original ones but are too short. Not happy with this transaction at all!!!

Removed the face plate above the door (2 Phillips screws.) Removed existing filter and replaced with the new one purchased. Reinstalled the face plate.

replaced with new one

I had to install my microwave, I order some parts like mounting plate and a ventilation grill .. took forever to get the parts from Part Select since I place the order to the day I received the parts took almost a month... I called several times and the rep. reponse was call again tomorrow.. GREAT!!! other than than the repair took me only 5 mins...

I followed the manufacturer's installation instructions. Everything worked perfectly.

when I opened the back cover of microwave, the diode was kind of blackish blown, since there was light bulb and fan were still working, i thought it could be problem with any one of the components like; magnatron or capacitor or diode, so first replaced the diode and mica at the end of the magnatron duct, there was problem with door switch as well. i fixed that too. Now it is working. It cooks bit faster, Wondering why?

Removed one screw lowered glass cover removed burned out bulb replaced with new one put glass back reinstalled screw. Dune 5 minutes back in business

Glass plate arrived in less than two days. Placed the glass plate in Microwave and presto the microwave works like a charm.

This is an under the counter microwave. Simply removed the two screws holidng the vent grille on top of the unit, lift out the old charcoal filter, clean the vent fan exit surfaces then replace the filter and put the vent grille back. Be careful to not drop either of the two screws after one is installed as you will have to take the grill off and start the screw installation again unless you have a magnetic to retrieve the dropped screw. An easy five minutes at most to change.