MHE13XHQ1 Roper Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- LENNARD from BURNSVILLE, MN
- Parts Used:
- 4392027
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Would not start
Watched a you tube video prior to installing new switch. Followed the video which gave me confidence i was up to the task. After removing the touch pad I found my design was not exactly like the you tube model but I found the defective switch, replaced it and put the microwave back together. Works great. Again watch the videos
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from PEORIA, AZ
- Parts Used:
- WP8183507
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Microwave light, turntable, and heat were not working
Remove from cabinetry, take cover off and had a very difficult time removing the plastic form that has the switched in. Replace the lowest of all the switches, and then again very difficult time getting the plastic form back in. Some of the plastic even broke during the process but not any that could prevent it from working as it did before. I had ordered a fuse, 2 packs of 2 switches as there are 3 switches but only had to use 1 to get it working again. Tested after switch install, put the cover back on and reinstalled in the cabinet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stuart from STEVENSON RNH, CA
- Parts Used:
- WPW10143947
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
turtable not turnng
discovered upon further inspection the the plastic shaft coming out of the turning motor was melted. Had to stop repair and order that part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from NINE MILE FLS, WA
- Parts Used:
- WP8205176
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The 20 year old original vent grille brittled and snapped at the clip lip.
The replacement took about five minutes and the only tool require was a Philips screwdriver. I just removed the old one and slipped in the new part. The replacement vent grille sent by PartSelect was a perfect fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from RIVERVIEW, FL
- Parts Used:
- WP8205176
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave over 10 years old.
My microwave vent grill broke from age. Ordered the new vent, which came with clips. I installed it in about 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joshua from Hollywood, FL
- Parts Used:
- WP8205176
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The old grille had cracked in several places
You need a philips head screwdriver to remove the two screws at the top of the microwave, freeing the old snapped off clips. The new grille does come with the clips already installed, which I hadn't been sure of, since you can't buy the clips by themselves. Let me reassure you if you're wondering too. Snap the new grille in, tighten down with the screws from the top, and I was done. Took me seven minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael J from LORAIN, OH
- Parts Used:
- 8206232A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned out light bulb which lit the surface of the range.
Unscrewed glass panel, removed old bulb, cleaned glass panel and installed new bulb. Screwed panel back into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roland R from NORTH ANDOVER, MA
- Parts Used:
- 8206232A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lightbulb burned out
Removed one screw lowered glass cover removed burned out bulb replaced with new one put glass back reinstalled screw. Dune 5 minutes back in business
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- alfred from summerville, SC
- Parts Used:
- 8206232A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burnt Out Light Bulb Replacement
Open compartment, installed bulb, closed compartment
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Francis from Doylestown, PA
- Parts Used:
- WP8205489
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Outside of cabinet got hot & food inside of microwave did not get cooked
Replaced the diode (aka wire-vltge) in the HV circuit after removing cabinet cover using both the secure torx screw drvr & phillips head screw drvr. The hardest part of the job was finding the secure torx nut drvr tool on the internet & purchasing same.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ramo from Sylvan Grove, KS
- Parts Used:
- WP8183507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Stopped working completely
My wife was pushing a few buttons with her knuckle (hands were full)and the microwave just turned off. Just like we had blown a breaker. First I unpluged it. Then I removed the phillips screws of the front panel, and found and removed the ceramic fuse. 3 days later I received the new fuse in the mail, and put it in. I plugged the microwave back in and it works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- virginia from mattituck, NY
- Parts Used:
- WP8205176
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Grill vent screw holes broke
Went on very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from decatur, IL
- Parts Used:
- WP4359963
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
top cought on fire.
tock out part put new one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carter from McCordsville, IN
- Parts Used:
- 8206232A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burn't out bulb.
Removed the glass cover and replaced the bulb. Very simple.
Was this instruction helpful to you?
Thank you for voting!
Old filters were beyond cleaning
Simply removed front of Microwave, removed the old charcoal filer and inserted the new one. On the grease filters, removed both of them from bottom of microwave and slid the new ones in place. That's all there was to it. No tools required.
Was this instruction helpful to you?
Thank you for voting!