LMH2016ST (CSBELGA) LG Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- vic from Allen, TX
- Parts Used:
- 6600W1K001D, 6600W1K001C
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
When the MW door was opened a fan would start running. Close the door the fan would go off.
Removed the MW from the wall. Took the top screws off the air vent. Then removed the two screws holding on the display. I then moved the display to its side and it revealed the micro switches. I removed the plug in leads from the micro switch one at a time. I did this with all three micro switches only one at a time. I reinstalled everything and plugged it in. No more fans starting when the door is opened.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from SEVERN, MD
- Parts Used:
- 3501W1A019D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
food does not get hot, carousel did not turn, all other indicators worked
Read the troubleshooting section on this site. Figured it was an interlock problem because the food was not getting hot (magentron not turning on) and the carousel was not turning. Did not think both the carousel motor and magnetron failed at same time, thus indicated an interlock problem. The interlock switches are actuated by the door latch. Replaced the assembly locker piece with all three switches (only a $20 dollar part) and microwave was fully operational again. Wife and kids think I am a hero.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from ORCHARD PARK, NY
- Parts Used:
- 6600W1K001D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Door switch was burnt out
Removed outer cover
removed lower door switch
installed new switch
Wa La!
removed lower door switch
installed new switch
Wa La!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from NEWARK, DE
- Parts Used:
- 6324W1A001L
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Would not heat and made a buzzing or popping sound
Unplug the microwave. Remove the Philips head and safety Torx head screws along the bottom of the sides and rear of the microwave which hold the black cover on. Lift the cover up at the rear and slide it backwards to disengage the tabs on the front top. Remove the cover. Discharge the capacitor by shorting the terminals to each other and then ground. Do this with a well insulated object and be aware there may be a pop when you do this. Keep hands, etc. on the insulated part of the object (screwdriver handle, etc). There's a lot of stored energy in that capacitor. I'd advise first checking the diode to make sure its not bad. Replace it if it is. The Magnatron is held in with a couple of screws on the top and sides. Unplug the connector and remove the screws. Remove the Magnatron. Installation is the reverse of removal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from LAKE WORTH, FL
- Parts Used:
- MDX61912701
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken clip that holds the grill in place.
Not hard to replace. Just remember the clip goes under the top not on top of the top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EDWARD from NORTH EASTON, MA
- Parts Used:
- 5889W2A012H
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
the turntable ring broke
purchased a new one...thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Irving from BEDFORD, NH
- Parts Used:
- MJS47373302
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken glass
Just replaced the inner turn table glass tray
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harvey from COLUMBUS, NJ
- Parts Used:
- MJS47373302
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Replace broken tray
I opened the door and slid the tray into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from WOODBURY, MN
- Parts Used:
- MJS47373302
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken 14” glass tray
Simply set new tray on microwave rollers and insured glass groves fit on roller .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claude from PARK CITY, UT
- Parts Used:
- 5230W1A012B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Air Filter Replacement
Originally called it "grease filter" until I found very small print "air filter" on damaged original. Part #PS3527528
Slipped into place with ease -- right bottom of microwave
Slipped into place with ease -- right bottom of microwave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from ROSELAND, VA
- Parts Used:
- MDX61912701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Vent grill would not stay in place causing door to remain open
Inserted plastic lugs in place, slid to right and it fit perfectly!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aurelian from FOUNTAIN VLY, CA
- Parts Used:
- MDX61912701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Item made of plastic that brakes easily. So I need to replace it because it got loose
Simple remove one screw, remove the little broken plastic and then replace the entire filter cover with the new one and tighten the one screw on the top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RICHARD from CARY, NC
- Parts Used:
- 6549W1S013H
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
microwave turn table not working
Removed the phillips screws from the base.
Using a # 10 secure driver, remove the motor. (I recommend obtaining a secure star driver set to be sure you have the right size)
Replace the spacer, which is a separate part from the motor.
Reinstall the spacer and motor.
Reinstall the bottom panel.
Enjoy!
Using a # 10 secure driver, remove the motor. (I recommend obtaining a secure star driver set to be sure you have the right size)
Replace the spacer, which is a separate part from the motor.
Reinstall the spacer and motor.
Reinstall the bottom panel.
Enjoy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from OLD TOWN, FL
- Parts Used:
- 3861W2A006A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
quit working
the repair kit was useless the toggles were to big to go through the top the threads on the bolts interrupted the toggle i had to drill the holes thole to except the toggles I got bolts at the hardware store what a mess
Bob
Bob
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from LA VERNE, CA
- Parts Used:
- 6324W1A001L
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set, Wrench (Adjustable)
Unit would not heat
Used a Motor cycle Jack to remove both unites combined. Removed side panels exposing internal working parts. Removed nonworking Magnetron and replaced it with new Magnetron. The process was completed in about 1 hour.
Was this instruction helpful to you?
Thank you for voting!