LRM1260SW (CWHELGA) LG Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from Minneapolis, MN
- Parts Used:
- 5020W0A001B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The button that opened the door had plastic hooks break off.
I looked up the part number, with shipping it came to $16, and in one minute of installation time, I just gently pushed the button into the front using the original springs that pushed the button back out, and it just clicked into place, the microwave back in action.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- greg from minneapolis, MN
- Parts Used:
- 5020W0A001B, 4B72023B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door button retaining clips broke off. button would fall out of place
Inserted spring on middle post on button back side. Pushed button/spring into hole on front of microwave until clips engaged and snaped into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- fred from northfield, VT
- Parts Used:
- 6549W1S011B, 5889W1A003B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
AC Syncro motor went in microwave
I tested the motor with an OHM meter, saw it was shot. Broke the turntable off when I tried to take it out from inside where it's attatched to the drive motor.( The plastic was like glued or welded onto the shaft of the original motor ) Had to open up the removable trap door on the bottom to pull the one screw that holds the motor in. Swapped it out, pushed the new turntable back in, and turned it on. Works like new! great parts, fast shipping, great deal !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kiah from CARPINTERIA, CA
- Parts Used:
- 5889W1A003B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The plastic base that rotates under the glass plate broke.
Lifted up the glass plate, lifted out the plastic base that rotates and placed the new one inside. The piece that connects is shaped like a semi-circle, so I rotated it until is dropped into place. Then I put back the glass plate and it was finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henriette from Davis, CA
- Parts Used:
- 5889W1A003B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
super easy
saved me having to buy a new microwave. It was super fast delivery, had the part the next day! Amazing service and great customer support.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DONAND from OVERLAND PARK, KS
- Parts Used:
- 5020W0A001B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Microwave Button had broken plastic hooks causing it to pop out.
Replaced Microwave Button with new button and hooks. Repaire took one min. by just pushing the new button on the Microwave and it hooked on and did not pop out. Good for another 4 years maybe!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kent from wichita, KS
- Parts Used:
- 6549W1S011B
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
the turntable on the microwave quit turning even though the microwave would heat up
I removed the outer cover of the microwave and removed the bottom palte to access the small motor. i unplugged the old motor from teh wiring connector, removed (1) screw and motor came out. I reversed the proceedure with the new motor and it was finished.It was a piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Monticello, IL
- Parts Used:
- 6549W1S011B
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Turntable quit turning
Overall repair quite simple. Removed screws from the sides and rear of the microwave, then removed cover. Next, removed only the screws to separate the bottom cover. Removed the one screw in the AC Synchronous motor to remove the motor (had to use small screwdriver through a vent slot in the bottom to remove the screw). Unplugged and removed motor. Installation is the reverse of removal. Note: on the back of my appliance were 4 torx screws with a tamperproof pin in the center. I used the rotary tool to grind out the pins so I could use a regular torx bit instead of ordering specialty bits.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stan from New Bedford, MA
- Parts Used:
- 6549W1S011B
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Carousel would not turn. Small plastic drive shaft broken.
Pried cover off bottom-center of microwave. It seems to be either glued or lightly tack welded. Removed 2 small Phillips screws to remove motor. Disconnected electric feed by hand. Don't let go of electric wire or small screws. They will be hard to retrieve from behind the rest of the metal base. Reverse process to install new motor. Didn't try to put small cover back on.
Was this instruction helpful to you?
Thank you for voting!