LMV1813ST (01) LG Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Raymond from DEPEW, NY
- Parts Used:
- 6600W1K001D
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would not start when closing door.
Removed some cosmetic panels. Removed the assembly with micro switches. Examined the faulty switch by checking the clicking action of switch. Two others were ok by this method. Replaced the switch with new one. Works fine so far. Thanks to web site and YouTube videos.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl from MATTESON, IL
- Parts Used:
- MCK63604901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I had no problem it was quick simple and very very easy
Just snapped out the old one and snapped in the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from MILLINGTON, TN
- Parts Used:
- 3500W1A013R
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Micro Wave no heat all else fine. Also at times door would not shut properly.
Replace (after testing w/ohm meter) diode and locker holder. My door often would not close properly. Microwave let know by saying not shut properly. When disassembled found the top screw mount was hollowed out resulting in it moving on occasion when you close door. First remove casing (special safety torx head) needed for rear screws. Onc e removed all parts available to view or work on. Diode is on the capacitor so caution is needed when removing. Serious shock hazard if touched. Use insulated pliers to remove from capacitor and a phillips on the ground. Test with ohm meter Should have resistance on way and non the opposite. Replaced mine bad. Next the holder 2 phillips screws and its yours. Unplug each switch and remove. Take note to what wires go to what switch and what switch mounts where. Mine had 3 switches. Removed from old holder and put in new. Screwed holder back in place and left scrws loose till re wired. Once wired set the holder by lightly tighting the screws. Try the door till it seats properly ensuring that all 3 switches are working properly. If so thighten screws. If all seems to work as advertised, safely plug in and test unit if heats up un plug and put cover back on micro. Your all set. Happy heating.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alice from Trenton, NJ
- Parts Used:
- MCK63604901
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
the stirrer fan cover meltted after I forgot to put the food in microwave and turned the oven on
I received the part and my son put it in where it belonged and no problems
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from PINELAND, SC
- Parts Used:
- 6600W1K001D
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Door switch malfunction
Take cover off microwave. Check door switches to determine which one was faulty.Remove and replace faulty switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harvey from COLUMBUS, NJ
- Parts Used:
- MJS47373302
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Replace broken tray
I opened the door and slid the tray into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- thomas from NEWARK, DE
- Parts Used:
- 6912W1Z004B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
need to replace the Nite light bulb
unplug microwave Remove light bulb hatch unscrew light bulb replaced bulb place bulb hatch back on to microwave plug microwave back in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Irving from BEDFORD, NH
- Parts Used:
- MJS47373302
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken glass
Just replaced the inner turn table glass tray
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from WOODBURY, MN
- Parts Used:
- MJS47373302
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken 14” glass tray
Simply set new tray on microwave rollers and insured glass groves fit on roller .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stacie from Granbury, TX
- Parts Used:
- 6324W1A001L
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave would not heat. Convection still worked.
I verified I had 120 volts going into transformer when the microwave was supposed to be running. The capacitor and HV diode both tested good. Be sure to discharge the capacitor before working in this area. This isolated trouble to either the transformer or magnetron. The windings of the transformer measured good. So ordered a magnetron. It was very easy to swap. There were 4 screws and one connector. This fixed our microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Colonia, NJ
- Parts Used:
- 6600W1K001D
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
suddenly stopped working while in use
i unplugged the unit,unscrewed the outer shell so that all the wiring and internal components were visible.starting at the first of three micro switches i removed the slip on terminals installed the alligator clips too the wires so the switch would now be bypassed.i made sure the wires and clips were not touching anything plugged unit in and it worked.i then installed the new switch and closed up the outer shell
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from PURCELLVILLE, VA
- Parts Used:
- 4370W1A006B
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
The new part was too thick for the worn out plastic ring which is obsolete.
Needed to raise the part to match the ring. I used peanut butter to hold plastic shim while replacing to hold it in place. Built in Oct. 2009.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from LA VERNE, CA
- Parts Used:
- 6324W1A001L
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set, Wrench (Adjustable)
Unit would not heat
Used a Motor cycle Jack to remove both unites combined. Removed side panels exposing internal working parts. Removed nonworking Magnetron and replaced it with new Magnetron. The process was completed in about 1 hour.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RICHARD from CARY, NC
- Parts Used:
- 6549W1S013H
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
microwave turn table not working
Removed the phillips screws from the base.
Using a # 10 secure driver, remove the motor. (I recommend obtaining a secure star driver set to be sure you have the right size)
Replace the spacer, which is a separate part from the motor.
Reinstall the spacer and motor.
Reinstall the bottom panel.
Enjoy!
Using a # 10 secure driver, remove the motor. (I recommend obtaining a secure star driver set to be sure you have the right size)
Replace the spacer, which is a separate part from the motor.
Reinstall the spacer and motor.
Reinstall the bottom panel.
Enjoy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from OLD TOWN, FL
- Parts Used:
- 3861W2A006A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
quit working
the repair kit was useless the toggles were to big to go through the top the threads on the bolts interrupted the toggle i had to drill the holes thole to except the toggles I got bolts at the hardware store what a mess
Bob
Bob
Was this instruction helpful to you?
Thank you for voting!