LMV2083SW (00) LG Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- william from LA VERNE, CA
- Parts Used:
- 6324W1A001L
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set, Wrench (Adjustable)
Unit would not heat
Used a Motor cycle Jack to remove both unites combined. Removed side panels exposing internal working parts. Removed nonworking Magnetron and replaced it with new Magnetron. The process was completed in about 1 hour.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dick from SANDY, UT
- Parts Used:
- 6600W1K001C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Microwave fan would come on when door open. Timer and unit would not switch on.
I looked up my problem on the internet and found a very helpful video. Microwave on video was different brand but the internals and methods were very much the same. The video made it simple and easy to fix. Found the replacement switch on the LG parts site and ordered. Two different switch types. One with red switch, the other green. Part was $7.28. Saved a bundle in service costs. Here is the repair video.
https://www.youtube.com/watch?reload=9&v=_AglBJoHgDs
https://www.youtube.com/watch?reload=9&v=_AglBJoHgDs
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerome from TECUMSEH, MI
- Parts Used:
- 5889W2A015A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
one of the little wheels kept coming off the ring.
just lift the glass turntable off and take the ring out and put the new in and put the glass back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stacie from Granbury, TX
- Parts Used:
- 6324W1A001L
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave would not heat. Convection still worked.
I verified I had 120 volts going into transformer when the microwave was supposed to be running. The capacitor and HV diode both tested good. Be sure to discharge the capacitor before working in this area. This isolated trouble to either the transformer or magnetron. The windings of the transformer measured good. So ordered a magnetron. It was very easy to swap. There were 4 screws and one connector. This fixed our microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rene from MORENO VALLEY, CA
- Parts Used:
- 4900W1A001B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Wanted to see the instructions before I install it.
Wanted to see the instructions before I install it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benjamin from Anchorage, AK
- Parts Used:
- 6324W1A001L
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replacement of Magnetron
I UNPLUGGED the microwave and removed the cover, using a phillips and a Torx screwdriver for the machine screws. I set these screws aside, so as not to confuse them with the later encountered screws. I photographed the magnetron to assure proper placement of the 6 phillips machine screws involved in reassembly (marking the the locations on the old magnetron would do as well. I marked the old magnetron "old", to avoid later confusion. I removed the two screws holding the shields to the magnetron. I removed 3 of the 4 screws holding the magnetron to the microwave, leaving one of the top screws. I held the magnetron securely and removed the last screw, pulling out a the part of the magnetron that penetrated the microwave. I installed the new magnetron in reverse order. One problem I encountered was locating one of the six screws, which had been pulled into the old magnetron by magnetism.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nelia from Streamwood, IL
- Parts Used:
- 6324W1A001L
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
no heat
unplug the unit then pull down , lot of screws are on top. open the cover . you could see the parts that need to replace on the right hand side (heavy side). disconnect wires then test the parts that need to replace by a tester to make sure that it's really broke .then unscrew part and replace .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marianne from CHURCH HILL, MD
- Parts Used:
- 6912W1Z004B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
light bulb replacement
very simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Samuel from Daleville, VA
- Parts Used:
- 3501W1A019D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave would not heat food, but everything else worked.
Problem was a faulty door latch switch. I easily accessed the switch by removing the control panel, total of 4 screws. After that, just disconnected the three switch door latch assembly and connected the new one. Took about half an hour and was very easy. Unit works perfectly now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Burke, VA
- Parts Used:
- 6912W1Z004B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light bulb burned out
I unscrewed the light cover, removed the burned out light bulb and replaced it with one I ordered on Partselect.com. It was very easy.
Was this instruction helpful to you?
Thank you for voting!