MV2041ASD LG Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Krzysztof from NEW BRITAIN, CT
- Parts Used:
- 5230W1A012B
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Leek
Change gasket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from WOODBURY, MN
- Parts Used:
- MJS47373302
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken 14” glass tray
Simply set new tray on microwave rollers and insured glass groves fit on roller .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from BIDDEFORD, ME
- Parts Used:
- MEB41908101
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken handle
Pulled off band unscrewed old handle and screwed on new one replace band
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RICHARD from CARY, NC
- Parts Used:
- 6549W1S013H
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
microwave turn table not working
Removed the phillips screws from the base.
Using a # 10 secure driver, remove the motor. (I recommend obtaining a secure star driver set to be sure you have the right size)
Replace the spacer, which is a separate part from the motor.
Reinstall the spacer and motor.
Reinstall the bottom panel.
Enjoy!
Using a # 10 secure driver, remove the motor. (I recommend obtaining a secure star driver set to be sure you have the right size)
Replace the spacer, which is a separate part from the motor.
Reinstall the spacer and motor.
Reinstall the bottom panel.
Enjoy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stacie from Granbury, TX
- Parts Used:
- 6324W1A001L
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave would not heat. Convection still worked.
I verified I had 120 volts going into transformer when the microwave was supposed to be running. The capacitor and HV diode both tested good. Be sure to discharge the capacitor before working in this area. This isolated trouble to either the transformer or magnetron. The windings of the transformer measured good. So ordered a magnetron. It was very easy to swap. There were 4 screws and one connector. This fixed our microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Irving from BEDFORD, NH
- Parts Used:
- MJS47373302
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken glass
Just replaced the inner turn table glass tray
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harvey from COLUMBUS, NJ
- Parts Used:
- MJS47373302
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Replace broken tray
I opened the door and slid the tray into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from ROSELAND, VA
- Parts Used:
- MDX61912701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Vent grill would not stay in place causing door to remain open
Inserted plastic lugs in place, slid to right and it fit perfectly!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claude from PARK CITY, UT
- Parts Used:
- 5230W1A012B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Air Filter Replacement
Originally called it "grease filter" until I found very small print "air filter" on damaged original. Part #PS3527528
Slipped into place with ease -- right bottom of microwave
Slipped into place with ease -- right bottom of microwave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aurelian from FOUNTAIN VLY, CA
- Parts Used:
- MDX61912701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Item made of plastic that brakes easily. So I need to replace it because it got loose
Simple remove one screw, remove the little broken plastic and then replace the entire filter cover with the new one and tighten the one screw on the top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from LA VERNE, CA
- Parts Used:
- 6324W1A001L
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set, Wrench (Adjustable)
Unit would not heat
Used a Motor cycle Jack to remove both unites combined. Removed side panels exposing internal working parts. Removed nonworking Magnetron and replaced it with new Magnetron. The process was completed in about 1 hour.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter J Baxter from Billings, MT
- Parts Used:
- MEB41908101
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
First problem was removing the vent cover. There were four screws that were not obvious that held the cover on. Reinstalling the cover also proved to be difficult due to alignment problems. Once that was done, the second problem was removing the door. There is a small, almost invisible, latch that h
At home on the kitchen counter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nelia from Streamwood, IL
- Parts Used:
- 6324W1A001L
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
no heat
unplug the unit then pull down , lot of screws are on top. open the cover . you could see the parts that need to replace on the right hand side (heavy side). disconnect wires then test the parts that need to replace by a tester to make sure that it's really broke .then unscrew part and replace .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benjamin from Anchorage, AK
- Parts Used:
- 6324W1A001L
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replacement of Magnetron
I UNPLUGGED the microwave and removed the cover, using a phillips and a Torx screwdriver for the machine screws. I set these screws aside, so as not to confuse them with the later encountered screws. I photographed the magnetron to assure proper placement of the 6 phillips machine screws involved in reassembly (marking the the locations on the old magnetron would do as well. I marked the old magnetron "old", to avoid later confusion. I removed the two screws holding the shields to the magnetron. I removed 3 of the 4 screws holding the magnetron to the microwave, leaving one of the top screws. I held the magnetron securely and removed the last screw, pulling out a the part of the magnetron that penetrated the microwave. I installed the new magnetron in reverse order. One problem I encountered was locating one of the six screws, which had been pulled into the old magnetron by magnetism.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marianne from CHURCH HILL, MD
- Parts Used:
- 6912W1Z004B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
light bulb replacement
very simple
Was this instruction helpful to you?
Thank you for voting!