KHMS155LWH0 KitchenAid Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- gary from jacksonville, FL
- Parts Used:
- 8184608
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the part disintegrated from heat and grease.
two screws placed at the ends of the part secured it to the microwave oven body.
Was this instruction helpful to you?
Thank you for voting!
Foreclosed home: parts were missing
Having the correct model number helps:
Just place the parts in the microwave and it worked.
Just place the parts in the microwave and it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from HARKER HTS, TX
- Parts Used:
- W11707984
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Microwave had no electrical
I was sent the wrong fuse by you. I had to procure a fuse in another manner. Very disappointing. The repair was simple. It just took longer because of the failure to send the correct fuse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ingrid from Roseburg, OR
- Parts Used:
- W10306627
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
had none
found info on the internet how to install it. No problems replacing the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herb from Auburn, IN
- Parts Used:
- W11707984
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
it was working fine and it stopped order a fuse and it wasn't the problem
took it to Buttermore appliance in Auburn Indiana and he changed the fan and added another fuse
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from SPRINGFIELD, WV
- Parts Used:
- W11707984
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Put the Fuse in, then plugged it in came on for a min then everything went out!!!!!
Took the front off and behind a plate was the fuse, so I replaced it for what good that did!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Maceo, KY
- Parts Used:
- 8169438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The microwave door would not stay latched, so it wouldn't come on.
The repair was easy, I just took off a few screws and found the broken latch spring. The real story is how easy it was to find the replacement spring from Partselect! I couldn't believe they had it, and even better yet, I ordered it one afternoon, and it came the next day with normal shipping! Unbelievable! Then I just popped it in and replaced the covers I had removed and it was working again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jorge from Bay Point, CA
- Parts Used:
- 8204670
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light bulbs nedd to repace it.
Took the the want burned out , and put the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Ft Lauderdale, FL
- Parts Used:
- 8205008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken vent grill for Kitchenaid microwave oven
I just looked at the broken one to see where it broke and looked at the microwave. I realized that there were two screws that were supposed to hold the vent grill along with 3 slots on the bottom. I inserted the slots on the bottom into the preset spaces for them, lined up the top with the two screws and screwed them into place. Checked to make sure the screws were not too tight and that was it. New vent grill in place and ready to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vicki from Phoenix, AZ
- Parts Used:
- 6802A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave Vent Hood Filters
Not so sure this would qualify as "instructions", but I only needed a screwdriver because the "D" rings of the old vent filters broke off and I had to pry to old ones out. Keep in mind, I am mechanically disadvantaged and can barely change an A/C filter ... that being said, all I did for this order was input my Model number and PartSelect found the correct replacement part. I receive the parts super quick (faster than the other 2 purchases I did that day). The only bummer was the packaging ... super huge box for small tiny parts. Otherwise, I now know where to go for replacement parts. This project should be a "no-brainer" for most DYI's, so getting the right parts with just a model number was lifesaving for me :0)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dotty from Hillsboro, WI
- Parts Used:
- 8204670
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
surface light on microwave wasnt' working
took the light assembly off and replaced the bulb and put the assembly together and fitted back in the space and finished the assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hugh from Potomac Falls, VA
- Parts Used:
- 8184264
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable), Wrench set
replace door handle
had to go on the internet to find out how to take front door apart..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from Woodridge, IL
- Parts Used:
- 8184264
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Replace door handle
Taking the door apart was easy once you figured out how it came apart. Youtube videos were not helpful as every brand of microwave is different; what works for one does not work for another. My Kitchenaide has little interior hooks on the inside of the door, 8 on top, 8 on bottom, 4 on the hinge side. You have to pry the door-skin up to get teh hook disengaged, then get a putty knife or similar to keep the hooks from re-engaging. Once you have about 6 or 7 undone, the door starts to come apart. Eventually the exterior of the door comes off; the interior of the door remains hinged. After that, you'll figure it out...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- thomas from orlando, FL
- Parts Used:
- 8184264
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Plastic Door handle broke off
Remove the 3 screws in the door. You will have to pry the door frame apart. use 1 or more flat screwdrivers to pry the inner liner from the medal door. There are plastic pieces that recess into the inner door from the medal frame. Once you get a few loose it is easy to remove the frame. Locate the 2 screws from the handle and attach the new handle. Then reverse the process to put the frame and inner door back together and put the 3 screws back in.
Was this instruction helpful to you?
Thank you for voting!