KHMS155LWH0 KitchenAid Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lillian from SAN JOSE, CA
- Parts Used:
- W10748097
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
my pan that browns the meat started to bubble and peal
I really did not have a repair on the microwave just a replacement of the browning pan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- SM from JAMESTOWN, RI
- Parts Used:
- 6800
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
On-door water/ice dispenser lights failed, paddles did not work to dispense
It took me time to remove the parts and suss out the issue, but the repair itself was EASY. A wire ribbon connected to the circuit board had gone bad. One Phillips head screwdriver, 7 screws, to get at the old one, pull it out, replace it with the newly ordered part. NO PROBLEM. Ladies, you can do IT!! You have the power!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GARY from PALM COAST, FL
- Parts Used:
- 8184149
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door Panel Was Cracked
Removed 3 screws on end of door panel and used a putty knife to separate door panel from door. Replaced with new panel and reinstaled screws. Very easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lea from FRANKLIN, TN
- Parts Used:
- 8184608
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken tabs
We took a chance on the less expensive black Whirlpool vent grille as I found online that it would fit our stainless steel Kitchenaid microwave. My husband was able to pry the stainless cover off the broken grille and snap it onto the new black one. Then just screw in the top screws to secure. We are very happy with the stainless/black of the new setup. It goes very well with the stainless/black of the cooktop and oven.
Was this instruction helpful to you?
Thank you for voting!
Very unusual. we had a brief fire inside the microwave which destroyed all the moving rotary parts.
First, we had to clean up all the interior surfaces, which was just cleaning. There was no internal damage. Then, just setting the center connector, rotary rollers and glass plate. Simple
Was this instruction helpful to you?
Thank you for voting!
The old coupling melted and the tray cracked in half.
It took me 15 minutes total - 5 minutes to clean the microwave, 1 minute to install three new parts, and 9 minutes to enjoy my celebratory glass of wine!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amelia from Charleston, SC
- Parts Used:
- 4393799
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
"Lost" microwave tray
Took out the turntable parts to ensure I ordered the correct cooking tray. Matching those with photos of related parts on PartSelect worked great. Put turntable drive and support ring in place and cooking tray went in very easily. Plan to order a second one to have on hand for this rental property.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Colan from Fargo, ND
- Parts Used:
- 8184608
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Vent Grill Fell Off
My vent grill fer me microwave done and fell off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Chapel Hill, NC
- Parts Used:
- 8184592
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
door was cracked, running through handle area
Having read a couple of other repair stories, I took out the screws (3 ea) on the end of the door and pried off the front door panel. There was a piece of glass sandwiched in between, and luckily it did not fall and break. Then I removed the handle, which was in good shape and installed it on the new door. The new panel snapped into place and I was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eldon from ORANGE, CA
- Parts Used:
- W10642989
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Turntable did not work
Ordered a new motor. Removed the outside trim of the oven-microwave combo. 2 screws at the bottom of the trim. Removed the screws that held the combination micro and oven unit in place. Removed the top and bottom black plastic grill of the microwave. 3 screws each. Pulled the entire unit out about 1 inch exposing the screws at each side of the microwave that hold it in place.
Snapped off the top control panel which exposed the wiring connecting the control panel.
Unplugged a couple of wire harness units to free the control panel.
Be sure to label the units to know which goes where during reassembly.
Remove the microwave unit from the housing and place it on its side.
Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.
Snapped off the top control panel which exposed the wiring connecting the control panel.
Unplugged a couple of wire harness units to free the control panel.
Be sure to label the units to know which goes where during reassembly.
Remove the microwave unit from the housing and place it on its side.
Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victoria from Mequon, WI
- Parts Used:
- 8184608
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Had broken previous grille
The most difficult part was getting the old screw out of the top of the grille. Once that was accomplished, the rest was easy as can be. I would highly recommend your service - very good! Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Naples, FL
- Parts Used:
- 8184608
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Original vent cracked and plastic connections broken
removed old vent and replaced by snapping in and two screws inserted into right and left top connections.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ellen from Upland, CA
- Parts Used:
- 8184608
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Grille broke off the microwave-fell off
Placed to new grille on the microwave and attached
with the screws.
with the screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Orlando, FL
- Parts Used:
- 8184608
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Vent Install
Easy to do. Remove the old screws where the tabs had been broken off. Install new vent and replace screws. MAKE SURE THE TABS ON THE BOTTOM ARE IN THE SLOTS.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mouang from Sacramento, CA
- Parts Used:
- 4393799
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Glass tray shattered
Ordered the glass tray and installed it. Received the orderin about two days.
Was this instruction helpful to you?
Thank you for voting!