36363692302 Kenmore Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Timothy from Swampscott, MA
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
microwave lamp was burned out
took glass cover off being an electrician and saw lamp or bulb was burned out. googled your site and with model number.went on partselect found lamp,orderd it.2 days later lamp arived installed lamp. So easy no running around or making several calls
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anita M from Rochester, NY
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Could not find the part at the big box stores - HD or Loew's
Removed the glass shield and inserted the 2 bulbs. Then replaced the glass shield.
The staff were terrific. Thanks so much as it had a happy ending.
Anita
The staff were terrific. Thanks so much as it had a happy ending.
Anita
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mack from Jacksonville, FL
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
No heat.
Replaced the fuse. Result; did not fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benjamin from Anchorage, AK
- Parts Used:
- 6324W1A001L
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replacement of Magnetron
I UNPLUGGED the microwave and removed the cover, using a phillips and a Torx screwdriver for the machine screws. I set these screws aside, so as not to confuse them with the later encountered screws. I photographed the magnetron to assure proper placement of the 6 phillips machine screws involved in reassembly (marking the the locations on the old magnetron would do as well. I marked the old magnetron "old", to avoid later confusion. I removed the two screws holding the shields to the magnetron. I removed 3 of the 4 screws holding the magnetron to the microwave, leaving one of the top screws. I held the magnetron securely and removed the last screw, pulling out a the part of the magnetron that penetrated the microwave. I installed the new magnetron in reverse order. One problem I encountered was locating one of the six screws, which had been pulled into the old magnetron by magnetism.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billy from Palm Desert, CA
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
failed bulb
unscrew one screw and remove bulb and insert new bulb and replace lense with one screw-
as easy as it gets-
as easy as it gets-
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from CUMMING, GA
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Had to replace to halogen lamps
Repair was simple; only a phillips head screw driver was required to remove the access plate.
Part Select delivered the replacement lamps within 3 days from the date I placed the order - great service.
Part Select delivered the replacement lamps within 3 days from the date I placed the order - great service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Laguna Niguel, CA
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Surface light bulbs burned out under microwave
Unscrew (one screw) and take off the cover of the surface light under the microwave (the light over the stove). Firmly pull out the old light bulbs. Align the two prongs of the new bulbs into the socket and firmly push into the recepticle. Replace the cover and screw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Madison, AL
- Parts Used:
- WB55X10428, WB10X10021
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would not operate after we noticed that the catch inside the door was broken
Removed the door, removed the old choke cover (breaking all the stap catches), removed the slide door latch assembly from the spring (the most difficult task) then reassembly of the latch to spring, sliding into the grooves along the inside of the door, the installing the new choke cover (very easy with the new one) taking care not the break any of the staps. Easy enough! Another difficult task was to re-install the door to the frame. It appears that the lower "hinge" is slightly bent down to allow easy install but the door now makes a slight sweeking sound when opening and closing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from Kernersville, NC
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
microwave won't heat
bought a fuse but that didn't solve the problem. Guess I need a new microwave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pines, from Middletown, NY
- Parts Used:
- WB49X10129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Had preheated the convection/microwave oven to bake 2 frenchbread pizzas for 25 minutes. Placed aluminum tray on top of glass plate with pizzas. 20 minutes into baking the plate cracked in half. Why? Don't know. Never had before.
Unpacked glass plate from cardboard box and placed atop rotating spindle inside oven - done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Kennett Square, PA
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light Bilbao burned out
Simple repair..took off covering with screwdriver removed the halogen bulb and replaced with the one I ordererd..wish all repairs went so well..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from Reno, NV
- Parts Used:
- WB25X10019
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Light bulbs had burned out.
I myself had difficulties replacing bulbs, as I have no feelings in my fingers, so I asked my son while holding the bulb in the bubble wrap, He had no problems what so ever.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Stephens City, VA
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
2 bulbs in the lower part of the unit had burned out.
Removal of the bulbs was easy; reinserting was not as easy due to the configuration/placement of the bulbs in the unit. It was interesting that a simple suggestion to keep the bulbs covered with some of the packing material made sense as to not directly handling the bulb itself and causing any contamination of the bulb(s).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Arlington, VA
- Parts Used:
- WB49X10129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken microwave glass tray
Placed the new tray in the microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from Boynton Beach, FL
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned out bulbs
One screw out - drop panel - remove and replace bulbs!!
Was this instruction helpful to you?
Thank you for voting!