36363692301 Kenmore Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dara from Tampa, FL
- Parts Used:
- WB55X10428
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Handle Broke off microwave
First I removed the vent on top. 2 screws had to be removed. Once plastic vent was removed I could lift door off. I then placed the door flat on counter top to get to backside of door. With 2 flat screwdrivers I pried apart the Door choke cover carefully as to not break the tabs. Its almost impossible not to break them. Thats why I ordered the replacement part. Good thing. I only broke 1. I could have reused it. However I chose to use the new one. Since handle in incorporated in the door, you have to take the door apart. I purchased the Door choke cover as well as a handle. After you remove the choke cover, remove the 6 or 7 small screws around the inner frame next. Now you can get to the door handle screws. Since the door handle broke off, you need to use needle nose pliers to hold the broken plastic on the outside of the door while unscrewing the inside screw that holds the handle. Once removed. replace the handle. Then carefully put it back the same way you took it apart. It took me about 15 to 20 minutes. Im a Female and thrilled I didn't have to call a repairman and get charged 200+
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry Totten from GROVES, TX
- Parts Used:
- WB24X10047
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Opened door to get food put more food in closed door it wouldnt work
Everything worked on the display light inside worked but when you closed the door and set time it would start counting down but not heating nor would the turntable turn. Started reading troubleshooting chart and first thing I did was removed the cover and checked door switches and found primary door switch wasn't working so I ordered a new one installed it and it worked. Anyone doing this has to be very careful because of the stored energy in the capacitor is strong enough to kill.
My micro is only 2 years old so I was hoping it wasn't anything major.
My micro is only 2 years old so I was hoping it wasn't anything major.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Bessemer, MI
- Parts Used:
- WB24X10047
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
mICROWAVE WOULD NOT HEAT
I REMOVED THE TOP PANEL OF THE MICR0WAVE AND THEN REMOVED ONE SCREW TO REMOVE THE CONTROL PANEL. rEMOVED OLD SWITCH. SNAPPED IN NEW SWITCH AND CONNECTED WIRE. REPLACED CONTROL PANEL AND UPPER PANEL.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Sandown, NH
- Parts Used:
- WB25X10019, WB10X10021
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
latch broke,bulb out
followed instructions posted on line.very good service .parts arrived in a speedy manner and were a perfect fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- pete from roslyn, NY
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Both undercabinet light bulbs blown
1. Open the cover over light bulbs with screwdriver.
2. Pulled out blown bulbs.
3. Inserts new bulbs from Partselect.
4. Tested new bulbs
5. Closed the cover over light bulbs with scvrewdriver.
6. Threw out old bulbs and packaging material.
Now, was that easy or what!
2. Pulled out blown bulbs.
3. Inserts new bulbs from Partselect.
4. Tested new bulbs
5. Closed the cover over light bulbs with scvrewdriver.
6. Threw out old bulbs and packaging material.
Now, was that easy or what!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Berwick, PA
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Halogen nite light bulbs had burned out
Parts arrived on the morning of the second day (Saturday) to my pleasant surprise. I opened the nite light access door with a screw driver. Inserted the 2 bulbs without touching the outside of the halogen bulbs. Checked that the bulbs did work and closed the access door. The entire process went quickly and posed very little difficulty.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- patty from SEATTLE, WA
- Parts Used:
- WB49X10129
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
the glass circular tray inside had cracked in half.It was of no use. I reordered another
The tray came within 5 days and I simply took it out of its well-packaged box and slipped it into my microwave. It is working just like new. I can't thank you all for being so punctual and reliable. better than having to buy a brand new microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Carrollton, TX
- Parts Used:
- WB56X10669
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Installing New Microwave
Required removing the old unit and disconnecting the exhaust ductwork and drilling new holes for attachment to the cabinet
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Colbert, WA
- Parts Used:
- WB06X10311
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old wave guide cover deteriorated from cleaning
Removed one phillips head screw, removed old cover, then replaced new cover and screw. Very easy and Parts Select made it happen. Will deal with them again. Thanks Parts Select.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Staten Island, NY
- Parts Used:
- WB06X10311
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Origional wave guide cover fell apart from harsh cleaners
Removed one Phillips screw, installed new wave guide cover, secured with phillips screw. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Orient, OH
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light burned out
removed screw that holds glass for light and replaced bulb.
Reinserted screw that holds glass.
Only down side was cost to ship small bulb.
Reinserted screw that holds glass.
Only down side was cost to ship small bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from NEWARK, DE
- Parts Used:
- 6324W1A001L
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Would not heat and made a buzzing or popping sound
Unplug the microwave. Remove the Philips head and safety Torx head screws along the bottom of the sides and rear of the microwave which hold the black cover on. Lift the cover up at the rear and slide it backwards to disengage the tabs on the front top. Remove the cover. Discharge the capacitor by shorting the terminals to each other and then ground. Do this with a well insulated object and be aware there may be a pop when you do this. Keep hands, etc. on the insulated part of the object (screwdriver handle, etc). There's a lot of stored energy in that capacitor. I'd advise first checking the diode to make sure its not bad. Replace it if it is. The Magnatron is held in with a couple of screws on the top and sides. Unplug the connector and remove the screws. Remove the Magnatron. Installation is the reverse of removal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dennis from harbor springs, MI
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Halogen lamps did not light-burned out
Removed the light cover screw with a Phillips screwdriver. Removed the lamps from the packaging just enough to free up the 2 prongs for fitting in the socket. Make sure the power is in the "off position". Install the bulbs one at a time by lining up the 2 sockets (Very important not to touch the halogen bulb glass surface while installing them). Energize the light switch to check operation of the new bulbs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Galen from SAN SABA, TX
- Parts Used:
- WB10X10021
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken microwave door latch.
Watched Utube instructions on how to do it to it and just did it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from SAN DIEGO, CA
- Parts Used:
- WB10X10021
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door latch broken
I read your instructions sent with the new latch. Looked at a couple videos online and it was VERY easy to change the part. Thanks so much?
Was this instruction helpful to you?
Thank you for voting!