JVM1870BF07 General Electric Microwave - Instructions

Microwave would not turn on--No lights--Nothing worked 1. Removed screws from back and side and pull off microwave cover. Be careful! There HIGH voltage back there due to a large capacitor that stores power. This capacitor is charged up even with Microwave unplugged. I checked the fuse located on top back part of Microwave. A lot of the time this is the problem but this time the fuse was good. I used an Ohm meter to check to see if there was an open circuit in one of the Thermostats. There are two of them in the Microwave. The Thermostats are about the size of a dime. One is located on the top right side and the other is on the top left side. One of them was bad. I ordered a new Thermostat. It arrived in just 2 days. I installed it and the Microwave was repaired and working great.

replacement door recommended $308.00 ! said no parts available ! I looked online and found one for $ 35.00 ! then i found your site and bought it for $3.00 !!! It came very fast. We looked up schematics on your site and looked on u tube for video of how to repair it. and my sons put it together in 15 minutes thank you!!!!!

took part of put new part on.30sec to do.

Amazing service. Order arrived within 24 hours!

Very easy ordered on line placed it in microwave

Removed the above stove microhood. Removed the side panels & the top panel. Diode located on right hand side of microwave. Removed with screwdriver & replaced new diode. It's best to get the microwave schematic online to pinpoint location of the part.

PartSelect had helpful repair instructions on-line which made the repair easier and faster. Unfortunately, there were other problems with the oven that immediately blew the new fuse I had just installed. It was then determined that additional repair would most likely cost almost as much as a new microwave.

After reading reviews that there was no power what so ever and a fuse replacement will solve the problem, I tried it. Replacing the fuse is very easy (and I am not handy at all). All you have to do is remove the microwave cover from the top by removing two screws, slide the cover to the left and pulling the cover off. Then remove the grill in front of you, by removing one or two screws. The fuse is in front of you, use pliers and be firm but gentle. Replacing the fuse is easy but it did not solve my problem.

thank you very much.

removed the bottom of the microwave and removed the motor and replaced the coupler and reassembled. Easy repair.

Trouble shot first by removing the digital read out face plate panel, lifting it up and out. Found the thermostat housed on the bottom section (found a picture of what I was looking for). It had two connectors. Removed the connectors and noticed that the one looked burnt/melted that was on the thermostat. Took paper clip, connected it with the wires to bypass the thermostat. Plugged in the microwave and power returned. Yes! Ordered thermostat part and changed it out. The new part didn't have a piece that fit exactly into the floor of the microwave so I just made sure it was secure to the bottom. It is only attached by 1 small screw. Fixed!

Once we noticed the turntable not working I removed the piece and noticed it was broken at the base of the coupler, took a vacuum and removed the broken piece and installed the new part. Thanks for the help!

The top edge of the microwave has a grill that had to be removed. To do that we took the two screws off and slowly slid the grill to the left before removing it. We had seen this on youtube. We have to be careful here because the grill has three plastic tabs that we cannot see. These tabs slide out from their tiny slots in bigger slots when we are sliding the grill to the left. The grill then comes off easily. No force is needed here so be gentle as much as you can. The charcoal filter can then be inserted in the microwave and tilted holding the front edge. The filter rests at an angle. The edges of the filter fits in the two corners of the space for the filter. The grill can then go back in place again with its tabs to slide in their slots slowly. Screws go back too. You now have a new charcoal filter for 6 months to a year depending on frequency of usage.

1. Unplug the microwave or switch off the breaker to the microwave. 2. Unscrew 5 screws on the bottom plate of the microwave. The plate swings down by the hinges on the back. 3. Unplug the wires leading to the turntable motor and make note of which color wire goes on which side of the motor plug. 4. The initial instructions said unscrew the screw holding the motor but my model has two screws. Remove the screws and lower the motor. 5. Insert the plastic coupler from inside the microwave through the hole in the center of the base. The coupler has a half moon shaped female shaft that connects to the male shaft that extends up from the motor. Slide the motor shaft into the plastic coupler. 6. Replace the screws that hold the motor onto the base of the microwave. 7. Plug the power wires back into the motor with the wires in the correct position as noted above. 8. Plug in the microwave and turn it on to check if the turntable now turns. Mine did not at first so I unplugged the microwave and the motor wires. It turns out you can plug the motor wires in and they don't connect correctly. I reconnected the motor plug and plugged the microwave back in and turned it on. This time the turntable was working. 8. Replace the five screws on the bottom plate of the microwave. Done.

Just like the directions said. Very simple.