JVM1870BF07 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ronald from Pinehurst, NC
- Parts Used:
- WB06X10144
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken turntable coupler
removed the bottom panel (6 screws), disconnected the two power terminals, and losened the turntable motor. installed the coupler from inside the microwave, replaced the motor, re-connected the power terminals, and bottom panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Queensbury, NY
- Parts Used:
- WB07X10416
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic tabs on Cam louver broke off and would not remain attached to microwave
Simply installed new cam louver to microwave with two screws. End of job!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clyde from Audubon, PA
- Parts Used:
- WB02X10733
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replace charcoal filter
Followed the easy directions that came with the replacement filter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Marana, AZ
- Parts Used:
- WB36X10071
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken light lense
Removed one screw, installed new lense in lense frame, rescrewed. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Warren, MI
- Parts Used:
- WB36X10071
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken lens.
Used a phillips head screw driver and loosened the lens frame under the microwave. Removed the broken lens and replaced it with the lens ordered. Put the lens frame back in place and secured it with the phillips head screw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Shawnee, OK
- Parts Used:
- WB24X829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
time would count down but unit would not run & heat.
remove cover, unplug secondary door switch (top switch)
remove switch from holder, install new switch, plug in wires, replace cover, very easy. door switches are a common problem
with microwave ovens.
remove switch from holder, install new switch, plug in wires, replace cover, very easy. door switches are a common problem
with microwave ovens.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mack from Jacksonville, FL
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
No heat.
Replaced the fuse. Result; did not fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chue from Cottage grove, MN
- Parts Used:
- WB26X10191
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The fan is not working.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from New York, NY
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No heat
Replace the fuses
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hugh from Slippery Rock, PA
- Parts Used:
- WB36X10071
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
glass light lens were broken
All one has to do is use a screw driver to remove the screws, one per lens.
Then lower the lens bracket, bend the 4 tabs holding the
lens, remove and replace the lens and screw the brackets back in place.
Less than 10 minuits.
Then lower the lens bracket, bend the 4 tabs holding the
lens, remove and replace the lens and screw the brackets back in place.
Less than 10 minuits.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lucinda from Burke, VA
- Parts Used:
- WB49X10063
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dropped the glass cooking tray while cleaning
after a couple of misfires, got the correct size tray, and replaced it in the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Shawnee, OK
- Parts Used:
- WB24X829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven wouldn't heat
remove cover-unplug wires from secondary switch-remove switch-snap in new switch-plug in wires-replace cover-works great. very easy to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jean from Lansing, MI
- Parts Used:
- WB56X10862
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
When we began a remodel we discovered there was no mounting plate on our microwave
Our remodler took only minutes to remount our microwave as it should be.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MANUEL from ESCONDIDO, CA
- Parts Used:
- WB27X10597
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
diode burnt
it was a simple screw in on both ends. no soldering
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Nashville, NC
- Parts Used:
- WB27X10810
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
miccrowave would not run.
removed housing. saw t-stat was burnt. replaced t-stat by removing mounting screw and installing new t-stat. reinstalled mounting screw. reinstalled oven housing. 15 minute job.
Was this instruction helpful to you?
Thank you for voting!