JES1290WJC01 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- JULIE from MACON, GA
- Parts Used:
- WB06X10591
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Microwave Was Popping And Shooting Fire Sparks
I removed the plastic plug that held the wavecover in place and pulled the wavecover off. I replaced with new cover and it worked perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Benicia, CA
- Parts Used:
- WB06X10591
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
GE Wave Guide Cover was fried, needed replacement
The wave guide cover (wgc) are notoriously bad on this model. As far as I can tell even a little food that gets stuck on it combined with cooking small/insubstantial items will cause the wgc to overheat and catch on fire. Ordered a part from partselect, found it very easily on their site using a nice diagram and ordered it. The item came in two days and was a cinch to pop in and replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hugh from Alexander, AR
- Parts Used:
- WB06X10591
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wave guide cover on fire
Remove white plastic button retainer (flipped out of my fingers and lost it. Found it 2 days later. Dog had chewed on it.) tabs on cover fit in nicely. New cover gets hot. Don't know if this is normal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- reval from ely, NV
- Parts Used:
- WB27X10743
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
blown fuse
Removed the three screws holding the cover on. then rmoved the two wires from the capacitor. Removed the screw holding the end of the zener diode to the chassis. Removed the diode from the capacitor. installed the new capacitor and replaced the blown fuse then reversed the removal process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- herman from franklin, OH
- Parts Used:
- WB06X10591
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
easy
no tools required. saved me from buying new microwave. glad i found this site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from RANGER, TX
- Parts Used:
- WB06X10591
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Microwave was popping and sparking flying
Removed the old wave guide cover and replaced it by slightly bending the wave guide cover and inserting 2 tabs on each side into the slots on the side of the micro/convection oven. I was ready to purchase a new appliance. Googled the model number, looked at a couple of sites and read the problems others had with this appliance and found my problem. I saved $$$ by purchasing the part and extended the life of my 11 year old appliance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebecca from EDINA, MN
- Parts Used:
- WB06X10500
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The original feet, two disappeared. Uneven microwave.
Fast & easy. I was able to determine that this foot would work from the descriptions on online!! Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from BEREA, OH
- Parts Used:
- WB06X10591
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
unable to push fastening button into wave guide cover without cutting or tearing
pushed guide cover into place without fastening to button
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Mobile, AL
- Parts Used:
- WB06X10591
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Replaced magnetron and spreader plate
on the kitchen counter. Removed parts and replaced exactly as the came off. insuring all fits were tight and secure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHARLENE from BURLINGTON, NC
- Parts Used:
- WB06X10591
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Just a little bit too big.
I had kept the old cover, just measured it against the new one, outlined it with a pencil, cut it to the correct size with a pair of scissors. Works perfectly now!
Was this instruction helpful to you?
Thank you for voting!