JVM1350BWC01 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Rick from Muncie, IN
- Parts Used:
- WB24X829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
microwave Quit working but lights worked
llation
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl from Winter Springs, FL
- Parts Used:
- WB06X10138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
glass turn table quit working
removed glass turn plate, removed broken coupler, went on-line and order the part on the GE website. It was really easy to determine the part number because of the diagram on the internet site, once I had the part number, simply placed the order. I was surprised how quickly the part arrived.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KAREN from MANSFIELD, MA
- Parts Used:
- WB36X10071
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light lens broke a couple of years ago
unscrewed the screw, pried up metal tabs that hold in light lens. took out broken pieces, slid in new light lens re-secured tabs with fingers, screwed in the screw again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Jackson Center, OH
- Parts Used:
- WB36X10003, WB08X10016, WB01X10063
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burnt out bulb and broken light socket
removed the bottom plate from microwave and replaced parts
Was this instruction helpful to you?
Thank you for voting!
Microwave will not start
Removed three screws from the top front cover and slide it out and following I removed the touch panel and the housing that holds the switches and replaced the bad one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norman from Voorheesville, NY
- Parts Used:
- WB36X10071
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken lens
remove two screws bend out flaps remove broken glass install new glas bend flaps back to hold glass install two screws. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from TREASURE IS, FL
- Parts Used:
- WB36X10003
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Under the microwave there are two light bulbs that light up the top of the oven/range.
Last week I removed the glass cover that was held in by one screw and removed the burnt out light bulb. I ordered the bulb and left the glass cover off until the bulb arrived. I had to wait until this evening to put the glass cover back on and fasten the screw because I have a window right next to the oven and the sun streaming in made it too difficult for me to see how to put the glass back in and replace the screw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tommy from Santa clarita, CA
- Parts Used:
- WB36X10071
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Previoous glass lens was broken
This repair was easy and could be done by anyone. If you undertake to do this replacement, remember to slowly bend the medal tabs back that hold the lens. Handled roughly these tabs could break off.
This repair can be don in under 5 minutes, easily !!
This repair can be don in under 5 minutes, easily !!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from MAYSVILLE, GA
- Parts Used:
- WB24X830
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave would run but not heat
Removed the control panel, one screw at the top. Removed 2 screws on the door switch holder and removed the door switch. VERY EASY.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from UNIVERSITY PA, MD
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bulb burned out light that is under the microwave, which lights the oven below.
thank you for the video--very clear, responsible, applicable although the illustration was not exactly of our kind of light. the bulb was exactly like the one Hotpoint used in its microwave made in 1989! I will come back to you for parts in the future. (You have the model # from my original order.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eduardo from San Antonio, TX
- Parts Used:
- WB15X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door handle broke
unscrewed the old handle and screwed the new one on really quick.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Ludington, MI
- Parts Used:
- WB08X10016
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Bulb broke in light socket
Tyring to get bulb out i ruined the light socket. Unscrewed the bottom cover of microware. Took out screw holding light socket, removed wires to socket with pliers, intsalled new socket. It was a piece of cake and the part was a perfect match.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOSEPH from NEDERLAND, TX
- Parts Used:
- WB15X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Handle
Replaced - unscrewed top screw, removed door gasket with spatula, reveiling bottom screw to unscrew. Replaced handle,screw back on and replaced door gasket. Follow instruction on web site. Help greatly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gail from Amherst, OH
- Parts Used:
- WB06X10138
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
arcing during use of microwave
Replaced turntable coupler by removing screws from bottom of microwave and reaching through to turntable motor. The screws were a little difficult to get to because of the proximity of the microwave to our oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Waterford, WI
- Parts Used:
- WB08X10016
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Burned out bulb
Screwed in new bulb.
Was this instruction helpful to you?
Thank you for voting!