JVM1730WMC01 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- charles from st augustine, FL
- Parts Used:
- WB36X10003, WB08X10016
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
the light over the stove top went out
I tried to replace a light bulb over the cook stove without turning off the power supply. The light socket had deteriorated and the bulb base shorted out on the microwave frame. I ordered new sockets and bulbs. Replacing them was s simple matter with the power off. However, there was still no lights working with the power on. I pulled to cover off on top of the microwave (two screws) and checked the fuse. Continuity test showed it to be ok. Next I pulled the cover off the control panel and pulled out the mother board. On the back side I noticed two burnt pins. I applied solder with a solder gun to replace the burnt off solder. I put it all back together and it works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randolph from Raleigh, NC
- Parts Used:
- WB08X10016, WB06X10165
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Light sockets were disintegrating
Removed the bottom plate screws from the microwave. Disconnect the wire harness. Replacement of the light sockets is easy. The female terminal connectors that connected to the bulb sockets were corroded, so I had to go to the hardware store and get replacements for those also. Replacement of those was unexpected but straightforward.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Littleton, CO
- Parts Used:
- WB24X10047
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Door Interlock Switch Failed
Removed cover, diagnosed problem, ordered part from Parts Select, received part in 2 days, replaced part, tested and replaced oven into built in space.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Bluffton, SC
- Parts Used:
- WB36X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burned out lightbulbs.
Changing 2 lightbulbs is NOT ROCKRT SCIENCE. With a screw-driver, remove the under MW light lens, unscrew the 2 burned out light bulbs, and replace with 2 new quality light bulbs. Test out that both are lite and working as they should, replace the lens and you are done, Until you find out one of the new (made in Chins) light bulbs is burned out after about 6 hours of being lite, call the parts phonr number and order a new replace bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paula from Camp Hill, PA
- Parts Used:
- WB06X10596
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grease filter not cleaned for 7 years !
Threw the old filter away and slide the new one in without any tools ! Filter should be cleaned every month - who knew ?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Denver, CO
- Parts Used:
- WB36X10071
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Glass cover for Light Bulb was cracked..
It was great...Thank you for having the part available...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PATRICIA from ALEXANDRIA, VA
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
replace micro/hood combo stove light
simply unscrewed protective lens cover, and swapped bulbs--these bulbs are great--last for years
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Arlington, TX
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned out light bulb in the over-stove microwave
Removed the one phillips screw that holds the light lens in place, drop the lens down for access to the burned out bulb, screw in the new bulb, replace the lens.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KENNETH from STRONGSVILLE, OH
- Parts Used:
- WB36X10003, WB08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burned out microwave light bulb and base broke off in light socket
Replaced light socket and bulb. Real easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pines, from Middletown, NY
- Parts Used:
- WB49X10129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Had preheated the convection/microwave oven to bake 2 frenchbread pizzas for 25 minutes. Placed aluminum tray on top of glass plate with pizzas. 20 minutes into baking the plate cracked in half. Why? Don't know. Never had before.
Unpacked glass plate from cardboard box and placed atop rotating spindle inside oven - done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from La Crescenta, CA
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light bulb burned out
Easy as can be. Removed one screw on the glass cover, removed two burned out bulbs and reinstalled two new bulbs, reinstalled the cover and all is well now. The best part - my 'supervisor' is happy that she can see to cook again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DALE from ST PETERSBURG, FL
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Over Stove Light Bulb Out
Took screw holding lens cover out, dropped cover down, unscrewed old bulb, screwed new bulb in socket. Screwed cover back in place. This is the third bulb in this socket, the other bulb is original.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kimberly from San Tan Valley, AZ
- Parts Used:
- WB49X10129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I broke the glass tray
I'm writing because I have never in my life had such an easy time finding a part, ordering it, and receiving it! Your service is truly unbelievable. I still don't believe it and I experienced it. Nothing went wrong and it could not have been easier. Please don't go away.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul g. from westlake village, CA
- Parts Used:
- WB49X10129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass rotating tray cracked and broke when cooking
This is the tray the glass cooking tray rest on and rotates the glass during cooking. The metal tray was installed upside down. The rotating glass tray was not properly installed. The oven was at a very high temp. and the weight of the utensil on the glass was not supported correctly. Result, big " pop " and broken glass tray. Note this is the second glass repaced. The first one dropped while removing it from the oven. It stuck to the bottom of the cooking dish and then fell to the floor. Pop, big breakage. Maybe you can learn from my mistakes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julia from Fairburn, GA
- Parts Used:
- WB36X10071, WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken light cover and blown bulb
easily replaced. parts arrived quicker than suggested. thanks
Was this instruction helpful to you?
Thank you for voting!