JVM1730WMC01 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bruce from Old Orchard Beach, ME
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burned bulb
removed the lens cover with one screw and replaced bulb
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ricardo from Port St Lucie, FL
- Parts Used:
- WB56X10723
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I broke door glass like the clumsy fool that I am
Decided best way to repair was replace the whole door. Yes it was a pricy repair, however I did not want the landlord to find out. I placed the old door with shattered glass pieces taped up in the box and disposed of properly and no mess.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ISAAC from MADAWASKA, ME
- Parts Used:
- WB49X10129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Glass Tray
Very easy replacement. Just lift out and replace with a new one!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elaine from Pittsburgh, PA
- Parts Used:
- WB36X10003
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
over range top light bulbs burned out
My son had to replace the bulbs because the screw that holds the bulb shield was so tight that I couldn't remove it. It was too difficult for me to do it myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from New Philidelphia, OH
- Parts Used:
- WB24X10047
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave would turn on ,BUT turn table would not turn and oven would not heat.
Took off cover , unpluged switches , took off switch assy, off/on test hooped and howlered for about 5 mins .Then laughed about other sites said could get those switches. Just wanted to say I LOVE Partselect. Super fast del , great price. JUST AWSOME!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jerry from gulfport, MS
- Parts Used:
- WB36X10071
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
glass broken
replaced the glass
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DON from CHEHALIS, WA
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no lights
Remove light cover. Replace bulbs Note. Light bulbs are 40W,Too much heat for bulbs & sockets
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from Puyallup, WA
- Parts Used:
- WB49X10129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass tray broke in microwave
Removed tray from shipping container and installed in the microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicole from Lathrop, CA
- Parts Used:
- WB49X10129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
drop and shattered the glass tray
It was so easy to order the part on this website. It came carefully packaged and quickly! Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from SUGAR HILL, GA
- Parts Used:
- WB36X10003
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burn ed out bulbs
I removed light bulb cover shield,took out defective bulbs and replaced with new ones. 5minute repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from San Marcos, CA
- Parts Used:
- WB49X10129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken micro tray
placed plate on carousel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from N Chesterfield, VA
- Parts Used:
- WB26X10208
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Turntable not working
Easy. A little awkward getting to the part since microwave is over stove and not much room between range and microwave. Other than that, it was a piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Boone, NC
- Parts Used:
- WB26X10208
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Turntable stopped turning
Removed the bottom panel from the microwave. Check to see if there was still power going to the turntable motor. There was still power there. Looked up the microwave model# on the website which showed a full display of the microwave parts. Selected the part. When the part arrived. Removed the bottom panel off the microwave. Removed the 2 screws holding the turntable motor in place. The new turntable motor was slightly different so I did have to cut a small slot in the new turntable motor so it would slide into the punched out slot so it would sit in the correct position. The job was still very easy and I complete the repair in about 20 mins. It was great to be able to do the repair myself and saved me some dollars. I would definitely recommend PartsSelect.com to anyone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Litteton, CO
- Parts Used:
- WB27X10017
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Microwave wouldnt heat but power made loud hum
Had to take the MW off the wall, remove the cover, and find the magnetron. Issue was the HV-capacitor. Had to remove the diode and capacitor to discharge the capacitor safely. Crackle-Bang! Then put it back before toying with the HV-transformer in order to get the magnetron out. Took a little under two hours to get it back on the wall and a lot of cajones when monkeying around the chassis removing the capacitor. Not a job for most everyone as this was a potentially high-shock repair due to the voltage and micro-farads held in that capacitor. Hardest part was getting the magnetron to drop out past the HV-transformer. Also, the thermostat had to be removed from the magnetron and re attached to the new one. Fiddly delicate job, not for the clumsy or faint of heart.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Walpole, MA
- Parts Used:
- WB36X10003, WB08X10016
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Bulb Light Replacement
I thought I could just unscrew the bulbs in the SpacemakerXL Microwave Oven. The bulbs melted into the bulb socket so every attempt to unscrew the bulb with pliers just broke the socket. So I took out the few screws holding up the bottom panel(with the bulbs and filters). I unplugged the electrical connection and took out the sockets but I used PAM Cooking oil on the electrical connections plugging into the sockets to avoid pulling the wire holders from the connection. Replacing both bulbs and the sockets at the same time makes sense since the heat from the stove melts the bulbs in the socket.
Was this instruction helpful to you?
Thank you for voting!