JVM1640WBC01 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- mark from oak lawn, IL
- Parts Used:
- WB26X10038
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
G.E. microwave turn table was loud and not working
I took it apart and found a small electric motor was not working . I couldn't find it locally so I ordered it from partselect and it was here in just a few days.the repair was easy only a few screws and plug it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from Blakely, PA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My turntable stopped working
I read several customer reviews before starting the repair. Removed the old drive motor to make sure I was ordering the correct part. Removal consisted of removing the screws on the bottom plate, disconnecting the electrical plug from the motor, and removing the one screw that attached the motor to the housing. Installation of the new motor was the reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry from Fort Stewart, GA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave noisey
Removed 5 screws to allow lower pan to hang down. Unplug motor, remove 2 more screws that hold motor in and pull it out. and reverse process for reinstallation of new motor. Took all of 4 minutes allowing time to drink a beer while taking the new motor out of the box
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Antonio from Colorado Springs, CO
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Glass cooking tray not turning
First I removed the 6 screws that hold the bottom panel in place. I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and then connected the two wires to the new element. Secured the element in place and replaced bottom panel.
Real simple process!
Thanks!
Real simple process!
Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PAUL from GRAND BAY, AL
- Parts Used:
- WB26X10038
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Glass Cooking Table Not Turning - Food Burning
Most mirco wave have a plate on the bottom to protect turn table motor. This one had no screws - it has 6 tabs holding the protective cover. Used pliers to tear tabs. Used philip's driver to remove screw and turned motor to come out. Went back in reverse order replacing motor. Left protective plate off
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from Olathe, KS
- Parts Used:
- WB26X10038
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
turntable would not turn
Removed five screws from the underside of the mircowave. Disconnected the two prong plug in. Removed the one screw that held the motor and replaced with new motor. Reconnected the plug and replaced the five screws
Tested the result with a bag of microwave popcorn. Worked perfectly.
Tested the result with a bag of microwave popcorn. Worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Mt. Juliet, TN
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
drive motor dead
This is the 3rd time I have used PartSelect to help me repair appliances I never thought I could fix on my own. The troubleshooting knowledgebase walked me through repairing my dryer, the illustrated parts diagrams gave confidence to replace the thermostat in my oven, and now to replace the tray motor in my microwave, all saving lots of money in my pocket instead of the repairmans. This motor repair simply requires removal of 4 screws, and unplugging an electrical connector. Hooray for PartSelect!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Irvine, CA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
turntable would not rotate
removed the screws holding the bottom panel, unscrewed the motor. Disconnected the motor. Connected new motor. Screwed in new motor. Replace panel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Sneads Ferry, NC
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the plate quit rotating inside oven
removed the srews under the unit unplugged the rotor motor and unscrewed 2 screws holding in the motor. When new motor arrived I plugged it up and put it on with the 2 screws and then put the bottom filter screen piece back on with the 6 little screws. REal, real easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Villa Rica, GA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
turntable wouldnt turn
easy repair. removed seven screws on the underside of the microwave and lowered the bottom cover. removed two screws from the old motor, unpluged the wires. reversed this sequence to install. took less than 5 minutes.
I had previously read these steps others had posted on partselect so the job was a breeze!
I had previously read these steps others had posted on partselect so the job was a breeze!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from Hampstead, NC
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turn table not turning
Removed the 5 screws that held the housing so it dropped down. removed the 2 screws to the motor. Disconnedted the plug. reinstalled the new motor. connected the plug and raised the housing and replaced the 5 screws. Took less than 10 minutes start to finish. Piece-of-cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry from Schoolcraft, MI
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
turn table would not rotate
As in other postings, remove six screws on the bottom of the microwave, disconnected the the plug,unscrew two screws to remove the old motor...(it took longer to get the new part out its box then it did to make the repair) unpacked the new part, put in the two motor screws, put in the six screws to hold the microwave bottom in place and waalaa...done!
Thanks,
Hank
Thanks,
Hank
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norman from Voorheesville, NY
- Parts Used:
- WB36X10071
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken lens
remove two screws bend out flaps remove broken glass install new glas bend flaps back to hold glass install two screws. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Vidalia, GA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
turntable did not operate properly
took 6 screws out of the oven bottom
removed 2 screws that held the motor
diconnected the power plug.
plugged in power to new motor, replaced 2 screws that held it in place, replaced 6 screws that held bottom of oven
That was it...
removed 2 screws that held the motor
diconnected the power plug.
plugged in power to new motor, replaced 2 screws that held it in place, replaced 6 screws that held bottom of oven
That was it...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GLENN from MANDEVILLE, LA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
it broke after 3 days and i was denied a new part or refund
it was easy . i unsrewed 2 srews and it went right in place
Was this instruction helpful to you?
Thank you for voting!