JVM1640WBC01 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from Littleton, CO
- Parts Used:
- WB36X10071, WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
glass light lens was broken, had collected grease, was dark.
Simply removed screw, pulled down light holder, unfoled the metal tabs, took out the broken pieces and replaced the glass lens and light bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Muncie, IN
- Parts Used:
- WB24X829
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
microwave Quit working but lights worked
llation
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bernard from McDonough, GA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The microwave was making a lot of noise and the glass plate was turning very slowly.
I diagnosed the problem myself. I googled GE parts and was refered to you guys. I ordered the part and it took less than a 5 days to arrive. I used a phillips scewdrive to remove the cover of my microwave and removed the turning glass motor. This took less that 30min and cost less that $50.00. I figured that it would have cost me approx $125.00 to get a tech person to my home for this repair.
Thanks a lot!
Bernard
Thanks a lot!
Bernard
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from McKINNEY, TX
- Parts Used:
- WB15X10023
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Had to replace the door handle on my microwave
I removed the inner bracket that held the glass in place with a nylon dish scraper that we use to clean our pots and pans with. It was safer than using a screw driver. I inserted the tapered portion of the scraper between in the bracket and the door edge on the inside of course,then slid it across the opening all around the door until the it separated. Making it easy to remove scews for the handle and the glass bracket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gloria from ROSSFORD, OH
- Parts Used:
- WB49X10129
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken Glass Cooking Tray
Placed the new tray into the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathie from Tipton, IN
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The turn table was making a terrible noise and wouldn't turn. I called a repair company and they told me it would be at least a hundred dollars to fix it.
I removed the screws that held the bottom in and then dropped it down to access the motor. I removed the 2 screws that held the motor in and unplugged it. I then plugged the new one in and reattached it with the 2 screws and put the bottom back on. It took me about 5 minutes to fix it for only $40.00.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terrence from Milton, FL
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Excessive noise while driving the glass tray.
Straight forward repair. The item came quickly, and since I had taken the other motor out previously to test it, the instalation was a breeze. There are a total of 7 external screws for the cover and two internal that hold the motor in place. One screw driver is all you need and access to the bottom of the microwave (I was fortunate that mine was an above the range model so accessing the bottom was easy). Anyone with a little manual dexterity can handle this repair now problem!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from UNIVERSITY PA, MD
- Parts Used:
- WB36X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bulb burned out light that is under the microwave, which lights the oven below.
thank you for the video--very clear, responsible, applicable although the illustration was not exactly of our kind of light. the bulb was exactly like the one Hotpoint used in its microwave made in 1989! I will come back to you for parts in the future. (You have the model # from my original order.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorraine from MIDDLETOWN, NY
- Parts Used:
- WB49X10129
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lawn mower would not start
removed cover over motor blew it out of leaves and dust. Removes 4 screws and removed piece ordered. The coil was rusted and not connecting. Changed oiece its working again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from TREASURE IS, FL
- Parts Used:
- WB36X10003
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Under the microwave there are two light bulbs that light up the top of the oven/range.
Last week I removed the glass cover that was held in by one screw and removed the burnt out light bulb. I ordered the bulb and left the glass cover off until the bulb arrived. I had to wait until this evening to put the glass cover back on and fasten the screw because I have a window right next to the oven and the sun streaming in made it too difficult for me to see how to put the glass back in and replace the screw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kip from POWELL, OH
- Parts Used:
- WB27X10928
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Not heat
-unplug
-remove top and front covers
-unplug wire connectors from heating assembly
-remove heating assembly from metal stand and push out of the way
-remove metal stand from dry
-pull out heating assembly
-install new one in reserve order
-remove top and front covers
-unplug wire connectors from heating assembly
-remove heating assembly from metal stand and push out of the way
-remove metal stand from dry
-pull out heating assembly
-install new one in reserve order
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Mt. Juliet, TN
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
drive motor dead
This is the 3rd time I have used PartSelect to help me repair appliances I never thought I could fix on my own. The troubleshooting knowledgebase walked me through repairing my dryer, the illustrated parts diagrams gave confidence to replace the thermostat in my oven, and now to replace the tray motor in my microwave, all saving lots of money in my pocket instead of the repairmans. This motor repair simply requires removal of 4 screws, and unplugging an electrical connector. Hooray for PartSelect!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Irvine, CA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
turntable would not rotate
removed the screws holding the bottom panel, unscrewed the motor. Disconnected the motor. Connected new motor. Screwed in new motor. Replace panel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Youngsville, NC
- Parts Used:
- WB26X10038
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Noisy Glass Cooking tray
The Glass cooking tray was very noisy. This was verified by turning off the tray rotation.
1. Removed the two metal filters.
2. Removed the screws holding the bottom cover of the microwave. 6 or 7 I believe.
3. Removed the two screws holding the drive motor in place.
4. Started the microwave with the motor hanging down to to verify it was defective. I could hear the motor rotating and making noise.
5. Replaced the motor, bottom cover, & filters in reverse order.
6. Tested, Works fine!
1. Removed the two metal filters.
2. Removed the screws holding the bottom cover of the microwave. 6 or 7 I believe.
3. Removed the two screws holding the drive motor in place.
4. Started the microwave with the motor hanging down to to verify it was defective. I could hear the motor rotating and making noise.
5. Replaced the motor, bottom cover, & filters in reverse order.
6. Tested, Works fine!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Bronston, KY
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Drive motor failed
I removed the screws (7) around perimeter of bottom. Don't remove the middle screw as it holds some gizmo in place. Dropped down hinged bottom. Removed motor (2 screws and a plug) matched to picture on website and ordered.
2 days later, part arrived, installed, good to go.
Bill, Kentucky
2 days later, part arrived, installed, good to go.
Bill, Kentucky
Was this instruction helpful to you?
Thank you for voting!