JVM1653SH06 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Janice M from Ft. Collins, CO
- Parts Used:
- WB07X10967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Had a broken Grill-Vent
Put in two screws!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carol from ridge, NY
- Parts Used:
- WB55X10813
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
the door frame was cracked and the glass was sliding down
once we figured out how to get the frame apart, the install of the new door frame was fairly easy..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norbert from Minnetonka, MN
- Parts Used:
- WB24X10047
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
No cooking Power
Had to remove outer cover (special screws involved). Found the correct part at PartSelect.Com and it arrived 3 days later as promissed.
This oven has diffcult electrical connections at switch to get disconnected. I found it easier with the sw loose and in hand so that the connectors can be released with a small screwdriver.
One has to this in order to test the part wirh an ohm meter. I found the sw did not close but remained open and thus caused the oven not to function.
Removing interconnect switch is tricky but not difficult.
Outer cover replacement is not as easy as it should be, especially the sides.
All is well and working.
Microwaves are simple devices if you are know how to read and understand schemetic diagrams.
This oven has diffcult electrical connections at switch to get disconnected. I found it easier with the sw loose and in hand so that the connectors can be released with a small screwdriver.
One has to this in order to test the part wirh an ohm meter. I found the sw did not close but remained open and thus caused the oven not to function.
Removing interconnect switch is tricky but not difficult.
Outer cover replacement is not as easy as it should be, especially the sides.
All is well and working.
Microwaves are simple devices if you are know how to read and understand schemetic diagrams.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from VIPER, KY
- Parts Used:
- WB27X10928
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Blown fuse in microwave
One small Phillips screwdriver and one fuse puller (I used cord). Unplug unit. Remove the two screws on the vent face plate. Remove the one screw on the panel assembly. Gently let hang. Pull the fuse located on the upper left wall. Replace fuse. Reassemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Erie, PA
- Parts Used:
- WB24X10047
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
microwave would not heat
First remove all screws holding on outer metal casing of microwave. Next remove the back and bottom metal pieces. You will then be able to pull aside the outer casing so you can access the door switches. Check each switch with an ohm meter in both the open position and with the switch closed. If the ohm meter reads the same in both the open and closed position, the switch is bad. Check the top switch first. Replace switch and reassemble. Cheap fix for a costly microwave. Great customer service at Parts Select!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Colorado Springs, CO
- Parts Used:
- WB02X11096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door latch broke where it hooks to spring.
Just pulled off the cover, removed the old latch, re-connected the spring...put it all back togeather. Everything just snapps back in. The entire repair took about two minutes. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from Lakewood, CO
- Parts Used:
- WB56X10669
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
I needed to acquire and install a mounting plate for an over the range microwave
I attached the mounting plate to the wall as directed in the installation instructions which I had downloaded from GE. This procedure took 45 minutes to complete. I was then able to mount the microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Seven from MOUNT AIRY, MD
- Parts Used:
- WB27X35382
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave not heating.
Followed the instructions on your website and a YouTube video. The diode was at a 90 degree angle which made it a little trickier. Unfortunately the repair did not resolve the problem. I ended up buying a new microwave for temporary use for less than ordering any more parts. We are pleased with your website, instructions, ease of installation though!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronie from BRIARWOOD, NY
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave does not have power at all, though outlet has power
unplugged power cable / unhooked front vent / unscrew the monitor panel / slide up to dislodge / take the fuse out and put in the new one in / fuse is located right in front of monitor panel once its open might be covered by wirings / you can unpin the cables from the panel to make it easier for you just make sure to put it back properly or you can have somebody hold the panel for you. Installing the fuse is easy waiting for the parts is crazy......
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Vero Beach, FL
- Parts Used:
- WB08X10022
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Bulbs were burnt out tried to remove them and the bulb broke from the socket
Moved the stove from underneath the microwave. Took the microwave down and turned it over. this need not be done. took the screws out to remove the bottom panel. there is a quick disconnect that need to be opened up. used pliers to remove the bad sockets and installed new one, used pliers to seat them. put bottom panel on, hooked up the quick connect. put the screws in and tightened them. installed bulbs and hooked up the electric and turned the lights on, they worked. installed the microwave, slid the stove back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Smithton, IL
- Parts Used:
- WB06X10689
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wheels would not stay on old ring
Removed turn table,removed old ring,put new one in its place, Put turntable back in and ready to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Tarpon Springs, FL
- Parts Used:
- WB36X10328
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Interior lamp burned out
Unscrewed the vent at top of microwave exposing small access to bulb. The access to this was very limited so that was the major issue in changing the bulb. You needed small hands to do the job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lenoma from NORTHGLENN, CO
- Parts Used:
- WB02X11096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Latch was broken you put spring on
Took off plastic around inside the door , took broken latch off and put spring on new latch on plactic on and it works . ????
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda sklar from JAMAICA PLAIN, MA
- Parts Used:
- WB49X10176
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
Broken glass turntable in microwave
Just placed it in microwave
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry Totten from GROVES, TX
- Parts Used:
- WB24X10047
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Opened door to get food put more food in closed door it wouldnt work
Everything worked on the display light inside worked but when you closed the door and set time it would start counting down but not heating nor would the turntable turn. Started reading troubleshooting chart and first thing I did was removed the cover and checked door switches and found primary door switch wasn't working so I ordered a new one installed it and it worked. Anyone doing this has to be very careful because of the stored energy in the capacitor is strong enough to kill.
My micro is only 2 years old so I was hoping it wasn't anything major.
My micro is only 2 years old so I was hoping it wasn't anything major.
Was this instruction helpful to you?
Thank you for voting!