JVM1790CK01 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Edwin from New York, NY
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No heat
Replace the fuses
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billy from Palm Desert, CA
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
failed bulb
unscrew one screw and remove bulb and insert new bulb and replace lense with one screw-
as easy as it gets-
as easy as it gets-
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from CUMMING, GA
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Had to replace to halogen lamps
Repair was simple; only a phillips head screw driver was required to remove the access plate.
Part Select delivered the replacement lamps within 3 days from the date I placed the order - great service.
Part Select delivered the replacement lamps within 3 days from the date I placed the order - great service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Laguna Niguel, CA
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Surface light bulbs burned out under microwave
Unscrew (one screw) and take off the cover of the surface light under the microwave (the light over the stove). Firmly pull out the old light bulbs. Align the two prongs of the new bulbs into the socket and firmly push into the recepticle. Replace the cover and screw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Duluth, MN
- Parts Used:
- WB06X10655
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
canopy mica cracking apart saging down mixer fan not working
remove 2 phillips screws from old canopy mica then a mixing fan and plastic retainer will fallout that holds the mixing fan in place. To install new canopy mica take your fingernail or something and scrap the three melted posts on the retainer that fits in new canopy mica on the retainer. If it is loose use a small amount of super glue to attach to new conopy mica to the retainer.Guide mica and glued retainer with fan up onto the post that runs the mixing fan.slide the right side corners in slots and tighten scews.preheat oven and good to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from La Grange, IL
- Parts Used:
- WB02X10750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
one of the rack holders melted and was not functional
I was so happy to find this part. I had been using an upside down glass bowl to level the rack! once I found part and it arrived it was in in less than 5 seconds!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Socorro, NM
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Quit working
Just like the directions said. Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Berea, OH
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Both Nite lights burned out, again.
So simple, unscrew the hatch underneath the microwave oven, pull out old bulbs, and insert new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Las Cruces, NM
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Surface lights burned out
Opened the cover. Removed burned out bulbs. Ordered replacements which arrived fairly quickly. Forgot to turn off power to unit (didn't matter in the end!). Using the bubble wrap the new bulbs came in, I inserted the bulbs one by one into their respective sockets. Not really tricky but the surface light is in the back of the microwave so I had to lean over the stove to get all the way back. Once in the bulbs worked fine. Closed the cover. All back to normal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kim from Poway, CA
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light bulbs burned out
Used screwdriver, removed cover, took out old bulbs and replaced with new ones. Couldn't get any easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from Reno, NV
- Parts Used:
- WB25X10019
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Light bulbs had burned out.
I myself had difficulties replacing bulbs, as I have no feelings in my fingers, so I asked my son while holding the bulb in the bubble wrap, He had no problems what so ever.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mohammad from Piscataway, NJ
- Parts Used:
- WB27X10928
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Powered Off completely
After reading reviews that there was no power what so ever and a fuse replacement will solve the problem, I tried it. Replacing the fuse is very easy (and I am not handy at all). All you have to do is remove the microwave cover from the top by removing two screws, slide the cover to the left and pulling the cover off. Then remove the grill in front of you, by removing one or two screws. The fuse is in front of you, use pliers and be firm but gentle. Replacing the fuse is easy but it did not solve my problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shirley from Collins, MS
- Parts Used:
- WB25X10019
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light on hood of microwave burned out.
Removed tiny screw from under the microwave that held the lid shut where the light was located. Took out old bulb and replaced with new one. Very easy!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from East China Township, MI
- Parts Used:
- WB27X10928
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
All power to the microwave went out.
PartSelect had helpful repair instructions on-line which made the repair easier and faster. Unfortunately, there were other problems with the oven that immediately blew the new fuse I had just installed. It was then determined that additional repair would most likely cost almost as much as a new microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from Pensacola, FL
- Parts Used:
- WB49X10176
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
turntable broke
No repair involved, just replaced......looked online and ordered, thought it would take 4-5 days, came in perfect condition within TWO 2 days. awesomeness
Was this instruction helpful to you?
Thank you for voting!