JVM1790CK01 General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- johnny from port orange, FL
- Parts Used:
- WB24X10047
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
no power in microwave in turn table wouldn't turn light would work act like door was open
remov cover to check voltage and found problem at the interlock switch ohm the switch and found it was open replace both switches it work fine now
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kim from Saint David, ME
- Parts Used:
- WB25X10019, WB44X10046
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench set
Convection oven not work in microwave.
I did some research and found the part through this website. Very easy to change the heater sheath, just took long to take everything apart. Looked at some diagrams to see exactly where the part was.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from CHARLOTTESVLE, VA
- Parts Used:
- WB25X10019
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light Bulb appeared to be burned out
The Halogen Light Bulbs for lighting the area below the microwave seemed to be burned out. I order new bulbs but by the time they arrived the old bulbs appeared to be working again. Not sure why this happened but I have new bulbs if they become burned out for good at some point.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- andrew from HOMOSASSA, FL
- Parts Used:
- WB56X35363
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
installed new kitchen cabinets
the problem was the mounting bracket that was installed when the house was built ,was not the bracket that came with the microwave. It was used to step the microwave out 3" in front of the other cabinets for the style that they were using then. so when I was installing the new cabinets I didn't want that style, so I ordered the original mounting bracket. It was a perfect fit and the install went great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- G. Wayne from GARDNERVILLE, NV
- Parts Used:
- WB21X10148
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
To heat a cup of coffee, user entered "10:00" instead of "1:00". Mess! After cleanup, microwave ran, but would not heat. While running, it made 2 or 3 time the noise volume as before.
I went for the cheap things first. Ohmmeter showed one of the thermostats in the magnetron compartment was open. I ordered and replaced all three thermostats. Still no heat. I took the unit off the wall (aaarrgh!) and checked the oven cavity thermal cutout. It said 7 ohms. I tested by shorting the wires together, but still no heat. So, I ordered the magnetron and diode cable. When replacing the diode cable (be sure to discharge the big cap!) either I broke it, or it was already damaged. It came off in two pieces. The new diode cable was re-enforced with thick heat shrink tubing, to prevent such breaking. You need a very short screwdriver to replace the magnetron. Now, all fixed! ~$150. A new one lists for $2000, installed in the overhead. My wife thinks I am a genius.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from Bedford, NH
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bulbs burnt out and needed to be changed
Ridiculously easy, unscrew, and change bulbs. Having the correct bulbs made all the difference, I did not have to waste time looking for the correct one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from New York, NY
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No heat
Replace the fuses
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DOMINICK from VENICE, FL
- Parts Used:
- WB25X10019
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bulbs Burnt Out
Removed old bulbs replaced with new. Bulb fit perfect thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Ashland, VT
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bulbs for sueface light burned out
Removed screw holding faceplate that covered bulbs. Next inserted new bulbs into sockets.
Turned on surface light to insure they worked - they did. Re-attached faceplate.
Turned on surface light to insure they worked - they did. Re-attached faceplate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norma from De Moines, IA
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The halogen bulb had blown
It was just a matter of removing the old bulb and easily putting the new one in place. Very simple repair and the bulb was received amazingly fast. Was no doubt the best service I have received and I appreciate the quick response.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anita M from Rochester, NY
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Could not find the part at the big box stores - HD or Loew's
Removed the glass shield and inserted the 2 bulbs. Then replaced the glass shield.
The staff were terrific. Thanks so much as it had a happy ending.
Anita
The staff were terrific. Thanks so much as it had a happy ending.
Anita
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mack from Jacksonville, FL
- Parts Used:
- WB27X10928
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
No heat.
Replaced the fuse. Result; did not fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerry from New Milford, CT
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
interior/exterior bulb replacement
Inside "cavity" bulb was a PITA. Need to remove top decorative trim (2 screws and tabs) to access bulb housing. Broke 1 screw tab so be careful (Wiggle it more). Acccess to bulb housing was made for younger smaller hands, attached by 1 screw. Remove screw, rotate housing, replace bulb. Reverse proceedure. Outside bulb, cake...1 screw, drop lens replace bulb, your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wilbert from Stephens City, VA
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light Bulbs Failed
Used a phillips screwdriver to remove the screw holding the light cover in place. Removed the two bulbs and replaced them. Closed the cover and tightened the screw
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Swampscott, MA
- Parts Used:
- WB25X10019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
microwave lamp was burned out
took glass cover off being an electrician and saw lamp or bulb was burned out. googled your site and with model number.went on partselect found lamp,orderd it.2 days later lamp arived installed lamp. So easy no running around or making several calls
Was this instruction helpful to you?
Thank you for voting!