JVM1740DP2WW General Electric Microwave - Instructions

I tried to replace a light bulb over the cook stove without turning off the power supply. The light socket had deteriorated and the bulb base shorted out on the microwave frame. I ordered new sockets and bulbs. Replacing them was s simple matter with the power off. However, there was still no lights working with the power on. I pulled to cover off on top of the microwave (two screws) and checked the fuse. Continuity test showed it to be ok. Next I pulled the cover off the control panel and pulled out the mother board. On the back side I noticed two burnt pins. I applied solder with a solder gun to replace the burnt off solder. I put it all back together and it works fine.

I thought I could just unscrew the bulbs in the SpacemakerXL Microwave Oven. The bulbs melted into the bulb socket so every attempt to unscrew the bulb with pliers just broke the socket. So I took out the few screws holding up the bottom panel(with the bulbs and filters). I unplugged the electrical connection and took out the sockets but I used PAM Cooking oil on the electrical connections plugging into the sockets to avoid pulling the wire holders from the connection. Replacing both bulbs and the sockets at the same time makes sense since the heat from the stove melts the bulbs in the socket.

Microwave would not turn on. Lights and fan worked fine. Before the microwave stopped completely, it would turn the microware fan on even when door was open. I read the reviews and they were exactly the same issue that others were facing. Once I opened the front panel and got to the switches it was easy to figure out which switch was bad as it was the one that was soft (When clicking it). It was hard to take it out though (it seemed stuck). So, I used a plier to yank it out. I put in the new switch and everything worked just great! I would like to thank other comments that were left on the site to make my task much easier. Thank you (to the commenters on PartsSelect), you not only saved me money, but also ensured that I learn about the microwave more and give me the confidence that I could fix it.

Fist I removed the 5 screws under the microwave. Then I dropped the panel and accessed the socket. I removed the socket by removing the one screw and disconnecting the wires. Replaced the wires on the new socket, installed the new bulb and reattached with the screw. replaced the panel with the 5 screws and I was done. Easy

Simple install. Thanks for your prompt response to my order and interest.

it was a simple screw in on both ends. no soldering

Took screw holding lens cover out, dropped cover down, unscrewed old bulb, screwed new bulb in socket. Screwed cover back in place. This is the third bulb in this socket, the other bulb is original.

Easy as can be. Removed one screw on the glass cover, removed two burned out bulbs and reinstalled two new bulbs, reinstalled the cover and all is well now. The best part - my 'supervisor' is happy that she can see to cook again!

unscrewed cover, took old bulb out, screwed new bulb in.relaced cover.

lower hood; support hood with spice rack;angle just right; unscrew light socket; remove wiring harness; replace; connect wiring harness;

Very simple disconnect light socket unit from snap in power supply replace socket with bulb screwed in reattach & back in business. Your service in supplying needed parts was par excellence. Thanks again

Using a #2 Phillips screwdriver and removed the screw that retains the lens frame around the broken lens. I also did the same to the opposite side (whose lens was fine but the bulb had been burned out for some time). With my fingers I pryed up the frame clips that secure the lens in place, removed the pieces of the broken lens, and replace the lens with one of the new lenses I had ordered. Although the bulb on this side was still burning, I replaced it with one of the two I ordered anyway. When I removed the bulb that was burned out, the glass separated from the bulb's base. However, I simply put on a set of tight fitting leather gloves and used my ring finger to apply pressure inside the base and it soon began to twist and then came out. This takes a little manual dexterity, but is very doable. If it were too tight, you could take a large "easy-out" tool (like the one to fit a 3/8" - 1/2" hole) and it would remove the broken base in short order. I had also ordered a second lens, but the lens on the burned side was simply dirty, so I cleaned it, put it back in place and saved the new one for a rainy day. By the way, BE ABSOLUTELY CERTAIN THE LIGHTS ARE SWITCHED TO THE "OFF" POSITION BEFORE DOING ANY OF THE ABOVE. Also take care to clean the glass on the bulbs with denatured alcohol and handle them with clean cloth gloves or a tissue so as not to allow any oils to be on the surface when they are switched on. Body oil will immediately create a hot spot which will shorten the life of the bulb by at least 50% if not more.

Getting the old bulb out of the socket was not an easy job as the factory seals the base of the bulb to the socket and for what reason I do not know. The seal has to be broken away to remove the bulb. I broke the seal with a knife and then proceeded to unscrew the bulb. The bulb at that point shattered in my hand and I was left with just the base of the bulb stuck in the socket. it took much effort to be able to work loose the base with a needle nose pliers and much sweat. The installation however went very smooth and Part Select did a fine job of sending me the right part in a very short period of time. They are a great source for any appliance part needed.

undid plate exposing bulbs. Bulbs were blown to the extent that I could not see the size or wattage. Went to website, got the data ... including how to find the model and serial number plate, entered the info, looked at the exploded drawing, ordered 2 new bulbs and 3 days later they showed up at our door FedEX.

Simply unscrew the bottom panel of the microwave device (it swings downward when opening - there are hinges on the back to protect it from falling down). Remove the old light socket (which is modular and is screwed in place)from the connectors and then replace it with the new light socket. That's it