JES1656SJ01 General Electric Microwave - Instructions

remov cover to check voltage and found problem at the interlock switch ohm the switch and found it was open replace both switches it work fine now

First I had to accept the fact that the unit was designed to keep non-professional people from doing any repairs. The switch was installed in such a manner that I had to break the mounting to remove the switch, then drill a hole in the mounting to secure the new switch in place.

Used a Motor cycle Jack to remove both unites combined. Removed side panels exposing internal working parts. Removed nonworking Magnetron and replaced it with new Magnetron. The process was completed in about 1 hour.

I first read where someone had the same problem. Their solution was a burned-out fuse. I ordered a new fuse...installed it and that did not solve my problem. I revisted PartSelect and read how Marla (from Arlington, TX)solved her problem. I purchased a secondary switch and when it arrived, I made a copy of Marla's instructions and followed them to the letter. I installed the new secondary switch into the secondary space, put everything back together and the oven STILL DID NOT WORK. I had to take the latching panel apart again and test each switch to see if there was another bad one. I found that the third switch was burned out. So I took the new switch out of the second slot and installed it into the third slot. I tested the switches before reinstalling the latching panel. This time everything worked. So I put everything back together, reinstalled the microwave on the wall, tested it again, and everything worked perfectly.

unplugged power
removed main black cover.
located part WB24X10047 and replaced

I previously replaced the turning motor because the gears in the old one were stripped. However, the new motor did not fix the problem. Upon examining the 3 wheels of the rotating ring guide, I noticed that there were flat spots on the wheels. When the motor tried to turn the ring, the wheels did not turn, but dragged, thus causing a major friction that eventually stripped the gears of the motor. Fortunately, I diagnosed the problem before the gears of my new motor were ruined. Replacing the rotating ring guide immediately fixed the problem.

I opened the door reached in give a steady pull up on the part it came out,I put the new one in pushed it down into place Bingo job completed Thank you

Replaced the fuse. Result; did not fix the problem.

Replace the fuses

I UNPLUGGED the microwave and removed the cover, using a phillips and a Torx screwdriver for the machine screws. I set these screws aside, so as not to confuse them with the later encountered screws. I photographed the magnetron to assure proper placement of the 6 phillips machine screws involved in reassembly (marking the the locations on the old magnetron would do as well. I marked the old magnetron "old", to avoid later confusion. I removed the two screws holding the shields to the magnetron. I removed 3 of the 4 screws holding the magnetron to the microwave, leaving one of the top screws. I held the magnetron securely and removed the last screw, pulling out a the part of the magnetron that penetrated the microwave. I installed the new magnetron in reverse order. One problem I encountered was locating one of the six screws, which had been pulled into the old magnetron by magnetism.

Simply took the part out of the package and replaced it. Good service - I recommend PartSelect.com

unplug the unit then pull down , lot of screws are on top. open the cover . you could see the parts that need to replace on the right hand side (heavy side). disconnect wires then test the parts that need to replace by a tester to make sure that it's really broke .then unscrew part and replace .

Replaced motor as a precaution as coupling had broken.

Parts shipped were all correct and good replacements.

We tried to follow the instruction on your website but our unit was slightly different. We had to take the stainless Steele outside shell off to remove the bottom to get to the motor. After removing the bottom, there was no wire mesh to cut through so this made it easier and less of a mess. The real challenge after installing the motor and getting the bottom cover back on was lining the stainless steel cover back to fit within all the grooves around the top and sides. It took 2 of us to get the tight fit correct. After that it was good to go! Thanks for the help and general guidance. I think ours was different because of the age and possibly the stainless steel model. We will definitely use your company again. The damage was absolutely human error. I placed a large heavy glass container in the microwave with handles that restricted the rotation. This jammed up the motor and the plastic cog on the motor broke off in the rotating ring. You do need to purchase both the motor and ring to completely repair this problem. Thank you, Lin

I have the built-in microwave in the cabinet. The hard part was getting it out of the cabinet. Once out, removing the cover and replacing the bulb and fuse was very easy. You need the tamper proof star bits to take out the screws holding the cover to the microwave. I got the bit set from Amazon for about $8. My fuse was OK. But I replaced it anyway, since it was 4-year-old. I am no expert in appliance repair, but found it fairly easy to do the repair. After unplugging the microwave, wait for 20 to 30 minutes before opening it, so that the capacitor inside completely discharges. It is supposed to discharge in 30 seconds, but why take a chance of electrocution..?