JVM3670BF09 General Electric Microwave - Instructions

lowered bottom plate of microwave then unscrewed little motor. put the new coupler in the hole from inside of microwave, then pressed the motor shaft on to the coupler .then just screwed it all together again.simple and no straining

Very easy ordered on line placed it in microwave

Microwave would not turn on--No lights--Nothing worked 1. Removed screws from back and side and pull off microwave cover. Be careful! There HIGH voltage back there due to a large capacitor that stores power. This capacitor is charged up even with Microwave unplugged. I checked the fuse located on top back part of Microwave. A lot of the time this is the problem but this time the fuse was good. I used an Ohm meter to check to see if there was an open circuit in one of the Thermostats. There are two of them in the Microwave. The Thermostats are about the size of a dime. One is located on the top right side and the other is on the top left side. One of them was bad. I ordered a new Thermostat. It arrived in just 2 days. I installed it and the Microwave was repaired and working great.

replacement door recommended $308.00 ! said no parts available ! I looked online and found one for $ 35.00 ! then i found your site and bought it for $3.00 !!! It came very fast. We looked up schematics on your site and looked on u tube for video of how to repair it. and my sons put it together in 15 minutes thank you!!!!!

took part of put new part on.30sec to do.

Removed the above stove microhood. Removed the side panels & the top panel. Diode located on right hand side of microwave. Removed with screwdriver & replaced new diode. It's best to get the microwave schematic online to pinpoint location of the part.

The exact part I needed was only 80 bucks or so, but I went ahead and got the whole assembly for 130 so I would not have to wait an extra 2 wks and risk having to stick it on the other assembly. I received the part fast, cuz it was in stock, just connected the smart board to it and attached the every connection. I screwed it back in place and put all the screws back in and bam!!!!. Just like new, no more beeping and everything is great. I did run a cooking 101 with everyone here to make sure they always turn on fan and make sure flame is under the pan size.

Watched How to repair a Microwave that turns on when the door is opened Video on the web. From this took a shot at the switch was the problem. When I removed the switch it was defective. The small button was in and when you turned the switch upside down the button would drop back into position. Ordered a switch for $25.oo , installed it and the microwave is working fine.

There are five Philips screws on the bottom outside cover .one at each corner and one at the front center. Remove all four at the corners .leaving the front center for last. When the last screw is removed ,the cover will hinge down, it is attached to clips at the back that allow it fold down. The wire attached to the light socket is connected by a pull apart plug. Grasp at each end of the hard plastic connector and pull outward ,DO NOT PULL ON THE Wires ! Lift the cover from the back of the microwave place it on a flat surface on a towel keep it from sliding around. Remove the screws holding the porcelain sockets. Reverse procedure to reinstall .Installing new Halogen lamps is suggested. Use a clean tissue or cloth to handle the lamps, finger prints on the lamp will shorten the life .

Loosen the two long anchor bolts that screw into the top of the microwave cabinet. These are usually in a shelf or cabinet directly above the microwave. Tilt the microwave forward enough to remove the 2 Phillips head screws from the top of the microwave cabinet. They are near the front. When these two screws are out, remove the fan vent. Once the fan vent is off, remove one screw that holds the control pad in place. Let it hang down. Just to the left of the control pad, you will see wires leading to three switches that close when the door is closed. Use a torx driver to remove the two screws that hold the switch bracket in place. With the bracket out, unplug the wire harnesses. On the opposite side of the wiring connected, a tab holds each switch in place. Lift the tab and slide the switches out. Usually, the bad switch will be identified by a loose or broken spring. Test them by pressing down on the switch. If you notice the bad switch spring, this is usually the bad one. When you have the new one, simply push it back into the appropriate slot and be sure that the holding tab snaps back in place. Plug the wires back in and re-attach the bracket. Put the control pad back on, then the fan vent. When down with those, push on the bottom of the microwave to lift it back into place and tighten the two anchor bolts in the top.

I replaced the cover just fine but i think a sensor went bad

slipped them into place by hand

every thing is working, but no hot

Uninstalled microwave from above range, removed cover then vent assembly (slide slightly to the left to free it). Opened the control panel (slide up then tilt forward) to access the troubleshooting/repair/test sheet. Followed the diagnostic flowchart and determined the TCO above the cooking cavity had failed. No other faults found. Ordered part Sat. afternoon and rcvd it Monday. Part is held in place with spring clips and quick connect terminals so installation was easy. Microwave was back in operation in no time.

removed the bottom of the microwave and removed the motor and replaced the coupler and reassembled. Easy repair.